New OP-COM 120309a - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Opel - Vauxhall - Holden (https://cartechnology.co.uk/forumdisplay.php?fid=59) +---- Thread: New OP-COM 120309a (/showthread.php?tid=4429) |
RE: New op-com 120309 - Cook - 01-07-2014 The HQ soft does not contain a modded exe Extracting the HQ Checksum code is easier than reconstructing the polymorphic VM code of the OPCOM exe. A Execryptor packed code is easier to analyse than a PECompact one...but that is only my point of view. RE: New op-com 120309 - biencomun - 02-07-2014 (01-07-2014, 14:35 PM)stmilosh Wrote:(01-07-2014, 12:57 PM)biencomun Wrote: my interface is ok i checked with 08-2010 version. What do you mean unmodded, my interface came with 1.45.You need to change FTDI Description to "OP-COM USB V2". How will I do that? Keep in my mind that my interface came with 1.45 and I think is one of the new clones that cannot be flashed. Thanks RE: New op-com 120309 - mattydr67 - 02-07-2014 Mate he said to change that in ept file from FTDI But you have to check first that your VID/PID is 0403/6001 in the device Manager Good luck RE: New op-com 120309 - biencomun - 02-07-2014 (02-07-2014, 07:36 AM)mattydr67 Wrote: Mate he said to change that in ept file from FTDI Sorry could you explain some more? I thought ept files are used to flash my device and I read that if i flash it it will get destroyed. Also if finally I can flash my 1.45 clone and have different VID/PID I will just have to change it in ept file? RE: New op-com 120309 - domelec - 02-07-2014 Ept file is used with program mprog3.5 U run the program with opcom plugged into PC and read its ftdi and change etc etc RE: New op-com 120309 - Maverickqwe - 02-07-2014 HI got this version of vaux com cant get it to work on win 7 32 bit but I have the 2008-20010en version working ok. Starts software ok test interface ok but will not connect to any ecu s on car latest drivers loaded. Comes up fake vid loaded and when starting diagnostics it comes up with a abox with vauxhaull in it click ok then goes into diagnostic menu ok but will not connect to cars ecu s RE: New op-com 120309 - biencomun - 02-07-2014 (02-07-2014, 12:38 PM)tango Wrote: Ept file is used with program mprog3.5 So is it safe even if I have fake chip? Also if my VID/PID is different will I just change it in ept? RE: New op-com 120309 - mattydr67 - 02-07-2014 Mate MProg and ept file it is to flash your FTDI chip not your PIC MCU If you are changing your firmware by flashing your PIC MCU you'll block it But changing the VID/PID in ept file for your FTDI chip will not affect your tool Good luck RE: New op-com 120309 - Maverickqwe - 07-07-2014 Hi can anyone tell me how to get car security pass number when using op-com or vaux-com please regards Tony RE: New op-com 120309 - domelec - 07-07-2014 Doesnt work on all cars iv only found it to get carpass for corsa c u have to go to eeprom |