+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: IMMO & LOCKSMITH (https://cartechnology.co.uk/forumdisplay.php?fid=9)
+--- Thread: Help damaged bsi on peugeot 307sw (/showthread.php?tid=4975)
Pages:
1
2
RE: Help damaged bsi on peugeot 307sw - daiyan - 25-06-2014
(25-06-2014, 22:46 PM)McMihai Wrote: I found the chip but when i read it with digiprog 3 eeprom obtion it just show fff on every line??? what to do?? were should the red cable on clip be on the chip?
please someone????
let's see Daiyan. is easier to change the eeprom from one unit to the other. than reading and writing, most of the time to do this you need desoldering eeprom
fussed all by yourself, or you really want to change the Km
[/quote]
first of all i want to get a bsi to run with my car since my original is total damaged. i have removed the chip, should i use digiprog 3 with it to read eeprom? and should i put the clip on the chip as is? would that not break the chip silver pins? and the clip have the red wire on it wich silver pin on the chip does the red wire goes on?
irst of all i want to get a bsi to run with my car since my original is total damaged. i have removed the chip, should i use digiprog 3 with it to read eeprom? and should i put the clip on the chip as is? would that not break the chip silver pins? and the clip have the red wire on it wich silver pin on the chip does the red wire goes on?
RE: Help damaged bsi on peugeot 307sw - domelec - 26-06-2014
Take EEPROM from damaged ecu and put to
One side then remove the EEPROM from new
Ecu and put in place the EEPROM u put to side
Making sure u put back on the correct way
Look for the little dot on EEPROM for correct way
RE: Help damaged bsi on peugeot 307sw - racin-snake - 26-06-2014
Get a used one .. virginise it ....code it with planet = job done least that way if it happens to it agin when you plug it in it aint a 350 notes bit of melted plastic
RE: Help damaged bsi on peugeot 307sw - daiyan - 26-06-2014
What is the drepa to virginize and How to code?
RE: Help damaged bsi on peugeot 307sw - daiyan - 27-06-2014
Do i need any special hardware to use with pp2000? and how does the steps goes to code with pp2000? what to code? i checked the eeprom from original bsi and i got that to work so now i have to put this eeprom in the donor bsi but what to program it and hot to virginize the bsi?
RE: Help damaged bsi on peugeot 307sw - domelec - 27-06-2014
U don't need to virginize anything
Just do as been said and replace EEPROM from old damaged ecu
To new donor ecu then the car will run
RE: Help damaged bsi on peugeot 307sw - daiyan - 27-06-2014
But what about the engine lock and etc?
RE: Help damaged bsi on peugeot 307sw - domelec - 27-06-2014
Why don't u just solder the EEPROM into the new bsi and then see?
Instead of making an easy repair into a very hard one
RE: Help damaged bsi on peugeot 307sw - paro44 - 30-06-2014
(27-06-2014, 13:47 PM)daiyan Wrote: But what about the engine lock and etc?
The needed informations for immobilizer are in the eeprom. The hardware of the bsi is equal, just replace the broken hardware and keep the needed "software"/eeprom.