+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: Mercedes Benz - Smart (https://cartechnology.co.uk/forumdisplay.php?fid=63)
+---- Thread: Xentry OpenShell PassThru 09-10-11.2016 (/showthread.php?tid=17898)
RE: Xentry OpenShell PassThru 09-10-11.2016 - CATAHA - 24-11-2016
(24-11-2016, 16:53 PM)stel_01 Wrote: Hi and thanks for the software much appreciated. do you know how to flash VAS5054 in order to work with xentry?Last Time i Flashed my Interface was when i Installed ODIS 2.7 ..... and to work with Xentry I DID NOT HAVE TO FLASH ANYTHING!!!!
To use Xentry with VAG-Interface you need SAEJ2534-1 For VAS 5054A software
that includes PassThru software
Read first post "3)Install PassThru Software and Drivers, Reboot, configure your PassThru make sure it's working and can be seen/tested and used in Windows "
RE: Xentry OpenShell PassThru 09-10-11.2016 - CATAHA - 25-11-2016
(22-11-2016, 19:04 PM)bibkare Wrote: According these pinouts pin8 is ignition at mercedes while at VW is some "CAN". Can this be true, what type of CAN uses pin 8. Strange. I will connect pin 8 with 1 and see will there be any difference.
UPDATE: Pins 1 and 8 does not have anything to do with voltage reading, there was no any difference i think it's a software problem because i could read live data from front SAM and it gave me correct voltage reading.
Could the file that i uploaded "Ignition" have an answer ?
[GLOBAL]
IGNITION =OFF
COMPORT = FREE ;--- FREE or BUSY, FREE is default
IGNITION_VOLTAGE = 12.0 ;--- float value with POINT as decimal separator
BATTERY_VOLTAGE = 12.5 ;--- float value with POINT as decimal separator
RE: Xentry OpenShell PassThru 09-10-11.2016 - bibkare - 25-11-2016
I tested and if leave like this "[GLOBAL] IGNITION =OFF " then no connection at all. There is another settings in C:\program file\mercdes-benz\DAS\bin\cal.ini where you can enable or disable passthru device to read voltage. I set value from 1 to 0 and then DAS shows value from global.sim BATTERY_VOLTAGE = 12.5 and if it is value=1 then shows IGNITION_VOLTAGE = 12.0. This was tested on VAS5054 however x-horse MVCI "see" correct voltage but can't connect to all modules for example it coudn't read SAM in ML164 while VAS5054 reads all modules.
RE: Xentry OpenShell PassThru 09-10-11.2016 - drovid - 27-11-2016
Hi, is this software support vans to?
RE: Xentry OpenShell PassThru 09-10-11.2016 - bibkare - 27-11-2016
(27-11-2016, 12:16 PM)drovid Wrote: Hi, is this software support vans to?
I tested on Vito 2008, works fine
RE: Xentry OpenShell PassThru 09-10-11.2016 - 61774058 - 03-12-2016
Hi,is this software can do SCN online coding?
RE: Xentry OpenShell PassThru 09-10-11.2016 - CATAHA - 03-12-2016
(03-12-2016, 09:28 AM)61774058 Wrote: Hi,is this software can do SCN online coding?That is an idea of passthru, to be able program new modules and code new modules
RE: Xentry OpenShell PassThru 09-10-11.2016 - bibkare - 03-12-2016
Todaj tested with DPA5, works better than VAS5054, correct voltage reading and it's 20% faster
RE: Xentry OpenShell PassThru 09-10-11.2016 - drovid - 12-12-2016
How install it to work with AVDI?
Sent from One+3
RE: Xentry OpenShell PassThru 09-10-11.2016 - CATAHA - 12-12-2016
(12-12-2016, 16:19 PM)drovid Wrote: How install it to work with AVDI?Same way as with VAS5054A first you install AVDI Software/drivers then passthru soft/drivers that are provided with AVDI and then Xentry!
Sent from One+3
If you still can not, then contact AVDI for help on installing passthru drivers/software
"FVDI" will not going to work, only "AVDI"