Xentry OpenShell PassThru 09-10-11.2016 - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Mercedes Benz - Smart (https://cartechnology.co.uk/forumdisplay.php?fid=63) +---- Thread: Xentry OpenShell PassThru 09-10-11.2016 (/showthread.php?tid=17898) |
RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 15-11-2017 HELLO Windows 10 native intaled 3 days ago I have VAS 5054A with serial #083600808 When I try to install drivers windows says "not found drivers" any idea/solution ? here pics of my vas5054a PCB the good think is that you don't need to unsoldering ram memories RE: Xentry OpenShell PassThru 09-10-11.2016 - Enabled - 16-11-2017 1. That is by far the worst VAS5054a clone I have seen. 2. You need to be on Win 7-10 32-bit and install the drivers correctly. See the instructions, they were very well written. RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 16-11-2017 1. That is by far the worst VAS5054a clone I have seen. That's I supposed 2. You need to be on Win 7-10 32-bit and install the drivers correctly. See the instructions, they were very well written. I do all but I plug vas5054a (I block W10 to install automatically drivers) I see Vas5054 i make "driver update" and i chose good place But I Have "no driver found" I suppose my vas5054 is very bad But work to read audi s4 b8 (usb mode only) RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 17-11-2017 Another question Tomorrow I can use original KTS of a friend How I can change vas5054a passthru to kts pasthru in xentry ? RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 02-12-2017 With a new vas5054a vci works fine with smart 450 (kiss point of clutch) smart 451 (kiss point of clutch) The only think is when ignition on/off : FIRST TIME USE THE KEY after change the file But don't work with w208.444 2002 normal or not ? RE: Xentry OpenShell PassThru 09-10-11.2016 - konstantin82 - 03-12-2017 No pass in DAS special function. Copy that file in folder where DAS instaled. I recomend not fully replace the old one. Just rename it. Then paste that file. RE: Xentry OpenShell PassThru 09-10-11.2016 - konstantin82 - 07-12-2017 (02-12-2017, 16:18 PM)HERVE06300 Wrote: With a new vas5054a vci works fine with I just create a 2 .bat files which replace the global.sim in DAS folder. And create shortcuts for them on a tasck panel. RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 12-12-2017 I try to change the file but not work When I start short test I have this : Ans when I try to open calculator I have : Start multiplexer fail Possible cause : the diagnostic system data sectors are not complete or defective contact help line RE: Xentry OpenShell PassThru 09-10-11.2016 - konstantin82 - 14-12-2017 (12-12-2017, 19:03 PM)HERVE06300 Wrote: I try to change the file but not work It's happens when you try to diagnose non CAN system. And system on K-Line which using not 7pin of obd2. In cars from 2005 Xentry Passthru, almost, works fine, except X463 (for mine expirience). On older cars different ecus using different pins in obd plug. To diagnose them you need a multiplexer. RE: Xentry OpenShell PassThru 09-10-11.2016 - HERVE06300 - 15-12-2017 Ok thanks a lot I will try to find multiplexer |