Clio II 1.5Dci injector test, need suggestion about the result - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Renault - Dacia - Nissan - Infiniti (https://cartechnology.co.uk/forumdisplay.php?fid=57) +---- Thread: Clio II 1.5Dci injector test, need suggestion about the result (/showthread.php?tid=18257) Pages:
1
2
|
Clio II 1.5Dci injector test, need suggestion about the result - Joda - 15-09-2016 Hi! Here is the problem: Car wont start but cranking. I done a leak off test of the injector until the cranking about 15-20sec. and here is the leak off test: The 1. and 3. injectors are very different from each other. The 3. injector returns 3x more fuel than the 1. injector. The other two injectors are continuously empty. What would be the diagnosis after a leak off patter like this? I have to say the car was by a Bosch specialist service for injectors and they told the customer the injectors are fine. Thanks. RE: Clio II 1.5Dci injector test, need suggestion about the result - pankar - 15-09-2016 The 1 and 3 have problem. They should not be leaking. RE: Clio II 1.5Dci injector test, need suggestion about the result - Joda - 15-09-2016 Could this problem conduct the car not starting situation? RE: Clio II 1.5Dci injector test, need suggestion about the result - pankar - 15-09-2016 Yes. if you clog metal tubes 1 and 3, will start the car with two cylinders RE: Clio II 1.5Dci injector test, need suggestion about the result - Joda - 15-09-2016 I'm not an injector specialist, I'm an electronic engineer and I'm doing electronic repairing on vehicles, but the customer comes back to me after the Bosch service ( where they told the injectors are fine ) and screaming for help. Should I screw out the metal tubes from injector 1 and 3 and check for clogging? Any suggestion would be great for me please. I wish to help my customer but I don't know actually how. RE: Clio II 1.5Dci injector test, need suggestion about the result - pankar - 15-09-2016 To start the car, the pressure should be above 300bar. Check with clip . if it is below, you clog the metal tubes 1 and 3 for test. The car must start. RE: Clio II 1.5Dci injector test, need suggestion about the result - banoo - 15-09-2016 (15-09-2016, 17:57 PM)Joda Wrote: I'm not an injector specialist, I'm an electronic engineer and I'm doing electronic repairing on vehicles, but the customer comes back to me after the Bosch service ( where they told the injectors are fine ) and screaming for help. Search in live data the rail pressure,and see what happen in starting,when the pressure is low(under 250bar)the engine will not start.The cranking rpm must circa 250rpm,this twoo things is must be for good starting. RE: Clio II 1.5Dci injector test, need suggestion about the result - pankar - 15-09-2016 Τhat is right minimum 250 bar. RE: Clio II 1.5Dci injector test, need suggestion about the result - Joda - 15-09-2016 Thanks very much for suggestion. What is the process to clog the metal tube? There is high pressure over 1000 bar or I'm wrong? RE: Clio II 1.5Dci injector test, need suggestion about the result - Gucci mane - 15-09-2016 Hello you have 2 Injector no working ... The Second from the left leak the forth look like have a good result ... |