CarTechnoloGY
Solved ✔ F30 FEM issue after ISTA+ programming - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: Solved ✔ F30 FEM issue after ISTA+ programming (/showthread.php?tid=19513)

Pages: 1 2

F30 FEM issue after ISTA+ programming - lynxbmw - 13-11-2016

Hello all,
We've run update procedure with ISTA+ 4.01.22 with ICOM NEXT on ZGW module and after flashing a pop up appear with message which said invalid IP or so. The procedure was not completely finish before this message. The process was aborted and car was strange inoperative - dash illuminated, tail lights and when tried to switch to ignition, fuel tank and temperature gauge were not working. Actually it is not possible to switch to ignition.
Before starting update procedure with ISTA+ we saved FA with e-sys. We've tried to load this FA and read SVT which is no more possible. Reading ECU instead shows only FEM_GW and no more modules in the tree.
Does anyone have an idea if FEM can be recovered/flashed somehow?
Thanks!

RE: F30 FEM issue after ISTA+ programming - winter - 14-11-2016

(13-11-2016, 20:20 PM)lynxbmw Wrote:  Hello all,
We've run update procedure with ISTA+ 4.01.22 with ICOM NEXT on ZGW module and after flashing a pop up appear with message which said invalid IP or so. The procedure was not completely finish before this message. The process was aborted and car was strange inoperative - dash illuminated, tail lights and when tried to switch to ignition, fuel tank and temperature gauge were not working. Actually it is not possible to switch to ignition.
Before starting update procedure with ISTA+ we saved FA with e-sys. We've tried to load this FA and read SVT which is no more possible. Reading ECU instead shows only FEM_GW and no more modules in the tree.
Does anyone have an idea if FEM can be recovered/flashed somehow?
Thanks!

Totally power off for about 30min by disconnecting battery connector and don't forget remove the charger,then re-flashing by ISTA+ 4.01.22.

RE: F30 FEM issue after ISTA+ programming - lynxbmw - 14-11-2016

(14-11-2016, 01:05 AM)lalaura Wrote:  BMW F30 2014 FEM coding by E-sys v3.22.5 in the text

@lalaura, it's not about coding FEM and by the way you have copied my instructions how to replace FEM from this forum into your blog.

(14-11-2016, 01:06 AM)winter Wrote:  Totally power off for about 30min by disconnecting battery connector and don't forget remove the charger,then re-flashing by ISTA+ 4.01.22.

Thanks @winter, but yesterday we left the car for 3 hours without battery and no change. Still cannot connect to the car, no ignition, no FA, only VIN is recognized somehow by ICOM.

RE: F30 FEM issue after ISTA+ programming - BMW888 - 14-11-2016

(14-11-2016, 12:30 PM)lynxbmw Wrote:  
(14-11-2016, 01:05 AM)lalaura Wrote:  BMW F30 2014 FEM coding by E-sys v3.22.5 in the text

@lalaura, it's not about coding FEM and by the way you have copied my instructions how to replace FEM from this forum into your blog.

(14-11-2016, 01:06 AM)winter Wrote:  Totally power off for about 30min by disconnecting battery connector and don't forget remove the charger,then re-flashing by ISTA+ 4.01.22.

Thanks @winter, but yesterday we left the car for 3 hours without battery and no change. Still cannot connect to the car, no ignition, no FA, only VIN is recognized somehow by ICOM.
Check FEM_GW in Esys. It may loss BTLD or SWFL. It is possible to flash back by Esys.

RE: F30 FEM issue after ISTA+ programming - shintake - 14-11-2016

You need to reflash it by esys via enet.

if you lucky that you have backup fa but if not you need to create you fa.

by the way you can pm. me for help

RE: F30 FEM issue after ISTA+ programming - lynxbmw - 15-11-2016

I do have FA backup which i load into Esys.
On reading ecu I've got only FEM_GW as I already mentioned.

RE: F30 FEM issue after ISTA+ programming - BMW888 - 15-11-2016

(15-11-2016, 15:49 PM)lynxbmw Wrote:  I do have FA backup which i load into Esys.
On reading ecu I've got only FEM_GW as I already mentioned.

According FEM_GW SVT. It is missing one SWFL (unknow_00000000_000_000_000).
Did you program it with ISTAP?

RE: F30 FEM issue after ISTA+ programming - lynxbmw - 15-11-2016

(15-11-2016, 16:27 PM)BMW888 Wrote:  
(15-11-2016, 15:49 PM)lynxbmw Wrote:  I do have FA backup which i load into Esys.
On reading ecu I've got only FEM_GW as I already mentioned.

According FEM_GW SVT. It is missing one SWFL (unknow_00000000_000_000_000).
Did you program it with ISTAP?
No, I program it with ISTA+ 4.02.14 where the failure happened. I've tried to import FA to ISTAP and do reanimation, but it asked me for I-level base, which I don't know.

RE: F30 FEM issue after ISTA+ programming - shintake - 15-11-2016

(15-11-2016, 17:51 PM)lynxbmw Wrote:  
(15-11-2016, 16:27 PM)BMW888 Wrote:  
(15-11-2016, 15:49 PM)lynxbmw Wrote:  I do have FA backup which i load into Esys.
On reading ecu I've got only FEM_GW as I already mentioned.

According FEM_GW SVT. It is missing one SWFL (unknow_00000000_000_000_000).
Did you program it with ISTAP?
No, I program it with ISTA+ 4.02.14 where the failure happened. I've tried to import FA to ISTAP and do reanimation, but it asked me for I-level base, which I don't know.

I level you can guess by VIN decoder

RE: F30 FEM issue after ISTA+ programming - lynxbmw - 15-11-2016

Tried to flash fem gw, but it ended with exception
Code:
Read SVT before TAL execution started.

TAL execution started.
ExecutionID=2016/11/15-20:54:21.936
[FEM_GW - 10] - [Exception - FEM_GW - 10] SVK-Ist does not match expected SGBMIDs for ecu ECUId:FEM_GW_0x10. Excpected (relevant process classes only): [hwap_00000f3d-255_255_255, hwap_00000f3b-255_255_255, hwel_00000792-000_005_002, hwap_00000f38-255_255_255, hwap_00000f3a-255_255_255], Actual (relevant process classes only): [hwel_00000792-000_004_003, hwap_00000f3a-255_255_255, hwap_00000f38-255_255_255, hwap_00000f3d-255_255_255, hwap_00000f3b-255_255_255], Missing SGBMID(s): [hwel_00000792-000_005_002], Surplus SGBMID(s): [hwel_00000792-000_004_003]
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "55s". [C206]

Read SVT after TAL execution started.
Read SVT after TAL execution finished.
I've entered i-level plant F020-12-07-500 and latest F020-16-11-502 which is selected I suppose based on my psdzdata.