DIGIPROG 3 user help thread ! - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: DIGIPROG 3 user help thread ! (/showthread.php?tid=261) |
RE: DIGIPROG 3 user help thread ! - Clusters - 07-06-2014 (02-06-2014, 20:25 PM)clusters Wrote: 2003 GMC Sierra no need solder chip use Avalanche OK, HUMMER -2007 should work also and can do hours. Confirmed today, 2004 Silverado Km and Hours adjusted using HUMMER/H2/HUMMER -2007 without soldering chip. This should work on all 2003-2006 GM Truck and SUV like Tahoe, Avalanche, Yukon, Sierra, Silverado and even Escalade. The KM programs within 100Km, desired 185,232 Actual 184,489, but the hours very accurate. They all use the S95P02 Eeprom 2003-06 full size truck and SUV. Do make a backup of Eeprom first! RE: DIGIPROG 3 user help thread ! - waynestewart123 - 17-06-2014 Does anyone know if the digiprog 3 is compatable with a suzuki alto? 2011 model? RE: DIGIPROG 3 user help thread ! - Chad69 - 25-06-2014 New to the forum I have digiprog 3 with all cables Obd I have tried on corsa 59 plate , ford focus 1999 , corsa 07 plate , a3 Audi 06 But don't connect says error no connection Can anyone confirm what year cars will work with this device it's 4.88 version thank you A list of cars it can work on and English manual thanks or something I can learn to use it correctly RE: DIGIPROG 3 user help thread ! - Clusters - 30-06-2014 (25-06-2014, 22:28 PM)Chad69 Wrote: New to the forum I have digiprog 3 with all cables I had problems with OBD cable too, opened it up and soldering of the wires to the board very bad, one touching another, but I haven't tried since. Edit: I used it yesterday and it communicates now on a vehicle that previously didn't, so check the internal wiring of the OBD2 plug. Follow the directions in manual for different cars, Google translate works well if all you have is German manuals. List of cars is out there all over the net. Hope some of this helps By the way, anyone have pinouts for the OBD2 connector, from db25 connector to the board inside OBD2 plug? Much appreciated. RE: DIGIPROG 3 user help thread ! - Fraz - 02-07-2014 Has anyone managed to do a C Class W204? Did you have to install CAN or do anything special? Or can it just be done by OBD? RE: DIGIPROG 3 user help thread ! - Avtoprofi - 02-07-2014 (02-07-2014, 14:40 PM)Fraz Wrote: Has anyone managed to do a C Class W204? Did you have to install CAN or do anything special? Or can it just be done by OBD? Mercedes w 204 2009 year W204 © – EZS - DIAG ok , 2 min W204 © - ASSYST - DIAG ok, 15 min If you do EZS BY OBD its change the km in ezs and the tacho! RE: DIGIPROG 3 user help thread ! - 666 - 03-07-2014 Hi all, A. Do we have a risk for EZS? Can Digiprog 3 flashes the ezs to 1.6million km? Can that happen? Yes/No? B. Do i need to start the engine when i update EZS and Tacho (Dash)? Yes/NO!!! C. If i good understand, if i flash EZS only, tacho will be updated also, so don't need to update dash (Tacho) after update EZS? Correct? Thanks 4 help Kinds Regards 666 RE: DIGIPROG 3 user help thread ! - Fraz - 03-07-2014 Hi guys, can anyone tell me if i can just do the Peugeot 207 2007 speedo or do i have to do the BSI too? Also do you have to remove the eeprom in the dash or can you do it without removing it? Thanks, RE: DIGIPROG 3 user help thread ! - vaidisvaidis - 03-07-2014 Dash + bsi,remove eprom RE: DIGIPROG 3 user help thread ! - canones76 - 04-07-2014 Hello very good i'm New Here I appreciate that this this forum. my question is I want to make a renault espace 2006 with gps and not in the manual, only the horn 2003 with the cable 47 and when I look in the digiprog v4.88 I get the cable 42 and not in the manual . anyone can help me would be helpful or someone already did Thanks in advance a greeting |