CarTechnoloGY
DIGIPROG 3 user help thread ! - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10)
+--- Thread: DIGIPROG 3 user help thread ! (/showthread.php?tid=261)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

RE: DIGIPROG 3 user help thread ! - mrmx - 01-07-2015

(30-06-2015, 22:32 PM)mrmx Wrote:  
(30-06-2015, 06:13 AM)Dayo Wrote:  Post a pic of the dash mate. Iv done a 64 plate via obd with digi, but it was the last of the old shape.
(30-06-2015, 21:59 PM)Dayo Wrote:  Where abouts are you mate?

im in timaru, new zealand

here is some pic's of the digiprog's on screen errors & end result fails on the mk4 2010 ford mondeo tdci diesel (cd345 ba7)

still needing help if possible? but if not even another product suggestion that will work for odometer correction on this car?

thanks again

RE: DIGIPROG 3 user help thread ! - Dayo - 03-07-2015

(01-07-2015, 03:19 AM)mrmx Wrote:  
(30-06-2015, 22:32 PM)mrmx Wrote:  
(30-06-2015, 06:13 AM)Dayo Wrote:  Post a pic of the dash mate. Iv done a 64 plate via obd with digi, but it was the last of the old shape.
(30-06-2015, 21:59 PM)Dayo Wrote:  Where abouts are you mate?

im in timaru, new zealand

here is some pic's of the digiprog's on screen errors & end result fails on the mk4 2010 ford mondeo tdci diesel (cd345 ba7)

still needing help if possible? but if not even another product suggestion that will work for odometer correction on this car?

thanks again
a 2010 mondeo should be 24c16 eeprom. if it says chip not found when you clip it, then you need to unsolder it. i dont recommend reading whilst on the board, but yes we all do it for ease.

so desolder and clip it in the clip. should be fine then mate.

click thanks wink
lexus is220 did as a is200 with 93c56 chip

RE: DIGIPROG 3 user help thread ! - mrmx - 06-07-2015

Ok,
i have found a chip that the pomona clip (5250) fits & is directly behind the lcd odo etc display in a cluster of components that are local to the lcd area also (see pic 1).
the chip has the numbers 33063v & pgsf on it? however there are two other chips the same that the clip will also fit directly beside each other that are further away from the lcd but have a different number (nxp t ja1040) on them both (see pic 2 end of pen..pic is upside down though).
any theories on this?
& if i put the digiprog on them while still on the board, will it first tell me that it can either read or not recognize without damage? & also if i turn the clip around the other way & try again? (i notice that the clip has a wee bit of black marker pen on one side, (as in pic 1..maybe negative? but which pin?)
the 2nd last pic is a close up of the last pic.

ive only ever had to use the obd port on cars to sort issues hence i am a bit unclear on this side of things & dont want to damage components etc, so any help to resolve this odo correction would be very much appreciated!

thanks all

RE: DIGIPROG 3 user help thread ! - diagtech - 07-07-2015

This is dash with 9s12 micro no eeprom on this

RE: DIGIPROG 3 user help thread ! - mrmx - 07-07-2015

Ok thanks,
so what can be done to do odo change for a new motor? is there another product that can? or upgrades for the digiprog? or any suggestions?

thanks again

RE: DIGIPROG 3 user help thread ! - scully - 07-07-2015

(07-07-2015, 01:08 AM)mrmx Wrote:  Ok thanks,
so what can be done to do odo change for a new motor? is there another product that can? or upgrades for the digiprog? or any suggestions?

thanks again

Hello mate. I've never not known digi not to do this speedo via obd. I have done lots of them via obd using v4.88. Does it light up orange/red when in car?

Smok ford will be your next option here I would have thought

RE: DIGIPROG 3 user help thread ! - mrmx - 07-07-2015

Hi thanks for your input.
does what light up orange/red? do you mean the lcd display( just to be clear?) & where can i get smok ford download from?
thanks again

RE: DIGIPROG 3 user help thread ! - scully - 07-07-2015

Yes the dash light up display ect. Smok is a company smok.pl

RE: DIGIPROG 3 user help thread ! - mrmx - 08-07-2015

(07-07-2015, 14:19 PM)scully Wrote:  Yes the dash light up display ect. Smok is a company smok.pl

ok, it did light up in either orange or red but ill check again today as to what colour & when etc. can i put a video up here or only pictures? ill video it just incase i can. thanks again

RE: DIGIPROG 3 user help thread ! - mrmx - 09-07-2015

(07-07-2015, 06:30 AM)scully Wrote:  
(07-07-2015, 01:08 AM)mrmx Wrote:  Ok thanks,
so what can be done to do odo change for a new motor? is there another product that can? or upgrades for the digiprog? or any suggestions?

thanks again

Hello mate. I've never not known digi not to do this speedo via obd. I have done lots of them via obd using v4.88. Does it light up orange/red when in car?

Smok ford will be your next option here I would have thought

ok so i tried again, & the same thing "unknown version". the dash, hazard lights & chime sounds all went off then all lite up in red/orange color as per norm for the lcd, & dash sounded again also.
didgiprog seems to run through a scan that takes a few second but it comes up "unknown version"
thanks again.
tried to upload a video but didnt work by the looks of things