DIGIPROG 3 user help thread ! - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: DIGIPROG 3 user help thread ! (/showthread.php?tid=261) |
RE: DIGIPROG 3 user help thread ! - beti88 - 26-03-2014 (25-03-2014, 20:44 PM)P206gti Wrote:(25-03-2014, 10:03 AM)beti88 Wrote:(26-01-2014, 22:27 PM)P206gti Wrote: Hi I have some questions : vw passat b6 2008 - there is I tested on my Passat with Tacho diag c32/c64 but it say NO CONNECTION. I Think it must be done by 24c32/servicemode as first step then Tacho diag c32 as second step to get it work. RE: DIGIPROG 3 user help thread ! - beti88 - 02-04-2014 (26-03-2014, 10:33 AM)beti88 Wrote:(25-03-2014, 20:44 PM)P206gti Wrote:(25-03-2014, 10:03 AM)beti88 Wrote:(26-01-2014, 22:27 PM)P206gti Wrote: Hi I have some questions : vw passat b6 2008 - there is Servicemod worked, but Tacho Diag C32 didn't work! RE: DIGIPROG 3 user help thread ! - stole - 09-04-2014 ALFA 156, 147 ,166, .... What is your experience??? RE: DIGIPROG 3 user help thread ! - NANO - 10-04-2014 Greetings, Quick question I cannot seem to resolve scanning the internet. I have 4.85 rev. unit and like others, when I connect to BMW OBD I get a mileage that is not correct from my car, it gives option to click no, and another wrong mileage comes up, so I am stumped, for even when I do hit check on one or the other wrong miles indicated, nothing changes. Unit appears to be working properly, but my confusion comes from some instructions that say I have to register DigiProg 3 first and install drivers on my computer? I have windows 7, and instructions are for XP which is different. Not being a computer geek, how do I install proper drivers to register unit as instructed, and is this required before unit will read proper mileage on my car. Thanks, RE: DIGIPROG 3 user help thread ! - JohnB - 12-04-2014 Hi guys i just bought this Digiprog III V4.85 does somebody know how to connect the ST01 to the chip? there are two ways and i dont want to damage anything.. one connection wire on the ST01 is red colored!! RE: DIGIPROG 3 user help thread ! - 23Andi23 - 12-04-2014 (12-04-2014, 15:43 PM)JohnB Wrote: Hi guys Friend welcome to Garage Automotive
First of all >>READ THE RULES<< Then your first post should be >>HERE!!<< RE: DIGIPROG 3 user help thread ! - gksuber - 14-04-2014 The red wire goes to pin No1 of the chip. Next to pin No1 there is a little hollow dot on the chip, look closely! RE: DIGIPROG 3 user help thread ! - octav_kiss - 16-04-2014 Hy I tried digiprog 3 on passat 2007 the gearbox wrong km wrote 0 and could not change RE: DIGIPROG 3 user help thread ! - cdipower - 16-04-2014 (16-04-2014, 14:53 PM)octav_kiss Wrote: Hy I think only reset funktion RE: DIGIPROG 3 user help thread ! - semcrer - 16-04-2014 Hello, I have a digiprog III v4.88 and I canĀ“t change the mileage via obd on a 2009 Ford Mondeo MK4 (the one with a large lcd sreen)! It connects but it can't read nor write the mileage. What am I doing wrong ? Can someone give me a tip or post the instructions ? Thank You, |