DIGIPROG 3 user help thread ! - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: DIGIPROG 3 user help thread ! (/showthread.php?tid=261) |
RE: DIGIPROG 3 user help thread ! - MC21 - 17-04-2014 I'm about to purchase the Digiprog3 4.88 to work on a Porsche 997. I see on the vehicle list: Porsche 997 MCU Program via chip Porsche 997 Tacho & MCU Programming Via Chips I have no idea what "via chip" means. Has anyone done this for the 997? Does it work properly? Anyone have a user manual so I can make sure it will work for me before I buy this? Thank you in advance. RE: DIGIPROG 3 user help thread ! - bochen - 19-04-2014 (17-04-2014, 16:55 PM)MC21 Wrote: I'm about to purchase the Digiprog3 4.88 to work on a Porsche 997.You need to open the dash , locate proper chip and read it by special clip with digi or desolder it and read in a programmer. RE: DIGIPROG 3 user help thread ! - MC21 - 19-04-2014 Okay thanks Bo, I get it now. Has anyone actually done it for the 997? Does the chip need to be desolder out? If so, I may want to look for other tools that uses the obd port. Anyone knows which one works? RE: DIGIPROG 3 user help thread ! - P206gti - 01-05-2014 (12-04-2014, 15:43 PM)JohnB Wrote: Hi guys The red is nummer 1 and some chips have a dot. The dot is the nummer 1 side. Or if you have the text on the chip on the Way you can read and place the st01 over it with the red on left side RE: DIGIPROG 3 user help thread ! - Avtoprofi - 01-05-2014 Hy here you have the right conections for the ST conectors, maybe it help someone ! Dont forget to thanks And the eetool softwer ! RE: DIGIPROG 3 user help thread ! - dleer2007 - 05-05-2014 Mb w212 cdi Partikelfilter Regenaration dpf by Delphi/Autocom Funktion RE: DIGIPROG 3 user help thread ! - juniorbeltran - 05-05-2014 Hello, I need to do a nissan sentra but it doen't appear on the list on my digiprog 3 any ideas?? RE: DIGIPROG 3 user help thread ! - Avtoprofi - 06-05-2014 Hy here the nissan manuals, look if its in ! Dont forget RE: DIGIPROG 3 user help thread ! - juniorbeltran - 07-05-2014 (06-05-2014, 00:32 AM)Avtoprofi Wrote: Hy Thanks but its not on the manual. I think I'm going to let it go but thank you RE: DIGIPROG 3 user help thread ! - Clusters - 02-06-2014 2001 Toyota Echo, use Yaris c46 OK 2006 Ford escape HCS12 OK 2002 Trailblazer no need to solder chip OK 2003 GMC Sierra no need solder chip use Avalanche OK, HUMMER -2007 should work also and can do hours. (05-05-2014, 23:24 PM)juniorbeltran Wrote: Hello, I need to do a nissan sentra but it doen't appear on the list on my digiprog 3 any ideas?? 2000-02 is 93C56 2005-07 is 93C66 Read save, edit and write using EEPROM and Tachosoft? Try other models? If read right, should program right. I never hurt eeporm reading it, only writing it. |