EDC16C34 _ECU_error_after_flashing - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: CHIPTUNING (https://cartechnology.co.uk/forumdisplay.php?fid=12) +--- Thread: EDC16C34 _ECU_error_after_flashing (/showthread.php?tid=37556) Pages:
1
2
|
EDC16C34 _ECU_error_after_flashing - powerwouz - 20-07-2018 Citroen C3 1.4hdi 2004 50kw EDC16C34 0281 011 861 9654490280 1039S05049 Software 9657061180 Engine code 8HX VIN CAR VF7FC8HXB27165384 After writing mod file (EGR OFF) STAGE 1 TUNE over OBD with kess V2, the ECU is locked, and don't have possibility to connect to ecu with DIAGBOX, flash tools KESS V2 or with Galleto. Car don't start and cooling fan starts spinning when the ignition is turned on. Before reading/writing over OBD I donĀ“t make full BDM backup... OBD reading no problem writing would not finish because with kess the right car was not in the list 1.4hdi 50 kw with bosch edc16c34 during the flashing the car was connected to stable power supply 13.5V . After flashing I wait 5 min without switch the ignition, after try to read ECU ID over obd and receive error. Can you help plz? kind regards, Wouter RE: EDC16C34 _ECU_error_after_flashing - semihmutcali - 20-07-2018 read it bdm and post the dump here RE: EDC16C34 _ECU_error_after_flashing - Jurik891964 - 20-07-2018 Would it not let you do the recovery via obd RE: EDC16C34 _ECU_error_after_flashing - powerwouz - 20-07-2018 (20-07-2018, 08:09 AM)Jurik891964 Wrote: Would it not let you do the recovery via obd No communication error... regards, wouter (20-07-2018, 07:28 AM)semihmutcali Wrote: read it bdm and post the dump here i order a bdm 100 set. next week....it will arive. regards, wouter RE: EDC16C34 _ECU_error_after_flashing - zoro1 - 26-07-2018 I dont think bdm will solve the problem.I think eeprom data is wrong too . RE: EDC16C34 _ECU_error_after_flashing - powerwouz - 26-07-2018 (26-07-2018, 14:21 PM)zoro1 Wrote: I dont think bdm will solve the problem.I think eeprom data is wrong too . You mean the modified file ? Do not correspond with the original file.. Or so?! I bought the modified file From somebody. Who said that he modified the original file egr off and stage 1 tuning... Can you advise me what too do? Kind regards, Wouter RE: EDC16C34 _ECU_error_after_flashing - senatormog - 26-07-2018 I hope you did save your native firmware? If so, try flashing it at low speed. I was able to recover my ebu without opening it. RE: EDC16C34 _ECU_error_after_flashing - ruben fernandes - 29-07-2018 i think the ecu its block...when cooling van comes on ecu its empty RE: EDC16C34 _ECU_error_after_flashing - zoro1 - 29-07-2018 (26-07-2018, 15:45 PM)powerwouz Wrote:(26-07-2018, 14:21 PM)zoro1 Wrote: I dont think bdm will solve the problem.I think eeprom data is wrong too . I,mm not talking abaut flash file,a say Eeprom file.eeprom is different inn all cars edc16,no matter the cars are the same.In eeprom content is injector codinng,milage,immo RE: EDC16C34 _ECU_error_after_flashing - Rov Gti - 29-07-2018 Write your ori file(read is ok) with BDM( maps). Then, after the car starts, write the mod file. For OBD read/write next time for these ECU's use MPPS. |