Cannot clear fault codes at DME and EGS - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: Cannot clear fault codes at DME and EGS (/showthread.php?tid=39689) |
Cannot clear fault codes at DME and EGS - ferbmw - 19-09-2018 Hi, I AM New AT THIS FORUM SO FIRST OF ALL THANKS FOR ACCEPTING ME. I AM USING ISTA D VERSION 4.13.14. I am having an issue when trying to clear fault codes at DME and EGS. I select DME or EGS, then call up ECU functions , then triger components, then clear faul codes and once selected, on the right side of the screen, it appears a msg saying: "This function has been deactivated due to obdII legislation". Do you have any idea why this function has been deactivated? My car was recently updated to i level 18-07-531 by the local BMW dealer and from then I cannot clear faul codes over these two modules. I could clear other errors that were present at IKha and FEM modules, but these other two modules show this msg. My car is a BMw 330 Sport Line year model 2016 AT. Thanks in advance RE: Cannot clear fault codes at DME and EGS - inspi1981 - 20-09-2018 Then clear fault codes regular way RE: Cannot clear fault codes at DME and EGS - ferbmw - 20-09-2018 (20-09-2018, 09:44 AM)inspi1981 Wrote: Then clear fault codes regular way sorry, but what do you mean by regular way? Thankd RE: Cannot clear fault codes at DME and EGS - torchia - 20-09-2018 (20-09-2018, 10:11 AM)ferbmw Wrote:(20-09-2018, 09:44 AM)inspi1981 Wrote: Then clear fault codes regular way Connect -> scan for errors -> show errors -> delete errors RE: Cannot clear fault codes at DME and EGS - ferbmw - 20-09-2018 (20-09-2018, 13:03 PM)torchia Wrote:(20-09-2018, 10:11 AM)ferbmw Wrote:(20-09-2018, 09:44 AM)inspi1981 Wrote: Then clear fault codes regular way ok. I did this today and I had to emulate a fault ( I disconet the MAF sensor ) and trigered the error. At that moment I tried to clear faul codes through the DME and again , showed the same msg. Then I look for the error in the general screen, and from there I could clear all ECUs, including DME. In the past, if there were some errors, I entered each ecu and cleared the faul codes from each one. It seems in this ista version, (or for this level 18-07-531??? ) , has been configured to clear fault codes through the general screen instead from from each ECU. However this is correct for DME en EGS; rest of the ECUs can be cleared from each module. RE: Cannot clear fault codes at DME and EGS - inspi1981 - 21-09-2018 So much time consuming RE: Cannot clear fault codes at DME and EGS - crazybm - 21-09-2018 First question is: which codes the DME and EGS have that you want to delete? Per the error description DME and EGS maybe looking at some error or failed component/sensor that has not been replaced For diagnosis follow the test plan if not faults found ISTA D may want to update the software in DME and EGS before allowing to delete the faults. |