+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: Renault - Dacia - Nissan - Infiniti (https://cartechnology.co.uk/forumdisplay.php?fid=57)
+---- Thread: CLIP error 104 module 5800 ?? (/showthread.php?tid=4042)
Pages:
1
2
CLIP error 104 module 5800 ?? - obdstart - 07-05-2014
At the first time in my life I have problem with CLIP device.
Software v137 ok, drivers installed ok, 4 LED light (2 red+2green), all looks like normal, but when try to connect with car I have from clip software message "error 104 module 5800.... try reconect for 10 sec. again"
Again & again reconect and same error.
Any have expirience with this error ?
Software bad or clip device damaged?
RE: CLIP error 104 module 5800 ?? - da14u - 07-05-2014
(07-05-2014, 20:19 PM)obdstart Wrote: At the first time in my life I have problem with CLIP device.
Software v137 ok, drivers installed ok, 4 LED light (2 red+2green), all looks like normal, but when try to connect with car I have from clip software message "error 104 module 5800.... try reconect for 10 sec. again"
Again & again reconect and same error.
Any have expirience with this error ?
Software bad or clip device damaged?
I GOOGLED IT FOR YOU 
RE: CLIP error 104 module 5800 ?? - obdstart - 07-05-2014
No too much info from mr.Google
RE: CLIP error 104 module 5800 ?? - da14u - 07-05-2014
(07-05-2014, 20:30 PM)obdstart Wrote: No too much info from mr.Google
But the link mentions it could be a loose connection, not necessarily externally it could be internal connection problem as well..remove screws and recheck all connections, make sure they're tight and good.
RE: CLIP error 104 module 5800 ?? - eudin77 - 07-05-2014
Read here,maybe you will find an answer.
RE: CLIP error 104 module 5800 ?? - da14u - 07-05-2014
(07-05-2014, 21:12 PM)eudin77 Wrote: Read here,maybe you will find an answer.
That's what I told him to look at
..did you check the first post link
RE: CLIP error 104 module 5800 ?? - admiral - 08-05-2014
(07-05-2014, 21:27 PM)da14u Wrote:(07-05-2014, 21:12 PM)eudin77 Wrote: Read here,maybe you will find an answer.
That's what I told him to look at
My friend, this is not an error, must have an aditional module to enter the mode OBD,,,,
(07-05-2014, 20:19 PM)obdstart Wrote: At the first time in my life I have problem with CLIP device.
Software v137 ok, drivers installed ok, 4 LED light (2 red+2green), all looks like normal, but when try to connect with car I have from clip software message "error 104 module 5800.... try reconect for 10 sec. again"
Again & again reconect and same error.
Any have expirience with this error ?
Software bad or clip device damaged?
My friend, this is not an error, must have an aditional module to enter the mode OBD,,,
RE: CLIP error 104 module 5800 ?? - obdstart - 08-05-2014
@admiral
I dont understand, what "aditional module" need for clip interface??
First time I heard of it..
Can not connect to Kangoo 2002 year 1.9DCi without aditional module?
Then f***k this interface
RE: CLIP error 104 module 5800 ?? - admiral - 08-05-2014
(08-05-2014, 14:46 PM)obdstart Wrote: @admiral
I dont understand, what "aditional module" need for clip interface??
First time I heard of it..
Can not connect to Kangoo 2002 year 1.9DCi without aditional module?
Then f***k this interface
my friend not need any additional module, , just need to choose the appropriate menu,,,,,if the 4 LED lights are lit, it indicates that you are ok, you can do diagnose,,, without any problem,,,,,,just open the program, insert the chassis number with 17 digits, click on the small icon next to chassis number,,,, then opens completely,,,, motor,gearbox
, the last column introduces a number 0 or 1,,, and say OK
RE: CLIP error 104 module 5800 ?? - obdstart - 08-05-2014
(08-05-2014, 15:41 PM)admiral Wrote:(08-05-2014, 14:46 PM)obdstart Wrote: @admiral
I dont understand, what "aditional module" need for clip interface??
First time I heard of it..
Can not connect to Kangoo 2002 year 1.9DCi without aditional module?
Then f***k this interface
my friend not need any additional module, , just need to choose the appropriate menu,,,,,if the 4 LED lights are lit, it indicates that you are ok, you can do diagnose,,, without any problem,,,,,,just open the program, insert the chassis number with 17 digits, click on the small icon next to chassis number,,,, then opens completely,,,, motor,gearbox
Everything are ok about 4 led lights, drivers, VIN etc... I do not use first time clip hardware in my life, but this coming new hardware from china from my some frend with this problem , then ask me for help.
Anyway thanks for help
, I will solve problem in next days, then give info here.