+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: How to disable parallel programming mode in Ista/P (Icom) (/showthread.php?tid=5949)
How to disable parallel programming mode in Ista/P (Icom) - hulahans - 19-08-2014
Does anybody know how to disable most parallel programming mode in Ista/P (Icom clone)
I don t know where i have to search for disabling this mode .
Somebody said this should solve my problem with flashing NBT on F Series,which has no separat most access like e series.
RE: How to disable parallel programming mode in Ista/P (Icom) - milkyway - 26-08-2014
Hello!
This will not solve your problem. The problem is not the most access, the problem is the dynamic IP.
Flashing the Most-ECUs (KOMBI, NBT, AMP, etc.) will work only, when the ICOM setting is set to DHCP (STATIC IP and APIPA will not work) and you have a DHCP Router in Network! Without a DHCP server (ICOM jump to APIPA) you will get error messages from Esys or ISTA/P (can not switch to paralell programming mode). Without a Router the only one way to flash these ECUs is: ENET cable.
CU Oliver
RE: How to disable parallel programming mode in Ista/P (Icom) - hulahans - 27-08-2014
Hi Oliver, thanks for your answer i have found it in another Forum too, but i have not tested it yet.
See you in MT
RE: How to disable parallel programming mode in Ista/P (Icom) - TizWoz - 27-08-2014
(26-08-2014, 10:07 AM)milkyway Wrote: Hello!
This will not solve your problem. The problem is not the most access, the problem is the dynamic IP.
Flashing the Most-ECUs (KOMBI, NBT, AMP, etc.) will work only, when the ICOM setting is set to DHCP (STATIC IP and APIPA will not work) and you have a DHCP Router in Network! Without a DHCP server (ICOM jump to APIPA) you will get error messages from Esys or ISTA/P (can not switch to paralell programming mode). Without a Router the only one way to flash these ECUs is: ENET cable.
CU Oliver
Are you saying that ICOM/ICOMA2 cannot program KOMBI, NBT ect without connected to router/network ? (OFFLINE?) unless you use Enet, then it is possible
is that all vehicle or just this vehicle or do I miss understand what you say ?
RE: How to disable parallel programming mode in Ista/P (Icom) - hulahans - 27-08-2014
Ista/P>Icom>NBT>without separate offline Router.Measuring plan works, and flashing all other modules. NBT ,Kombi don t work
Esys>Icom>deactivate parallel programming mode>NBT and all other modules work
Esys>Eth>NBT all other modules work
So the thing with ista p and offline router i have not tested yet.Only one person in another Forum tested it and for him it works.
I have found maybe another solution, there is a tool outside (tftpd32/64) that can make youre laptop act as an dhcp server without Router, maybe this works so you don t nee additional Router
Homepage with Infos for tftpd
http://philippe.jounin.net/tftpd32.html
RE: How to disable parallel programming mode in Ista/P (Icom) - TizWoz - 27-08-2014
(27-08-2014, 12:19 PM)hulahans Wrote: Ista/P>Icom>NBT>without separate offline Router.Measuring plan works, and flashing all other modules. NBT ,Kombi don t work
Esys>Icom>deactivate parallel programming mode>NBT and all other modules work
Esys>Eth>NBT all other modules work
So the thing with ista p and offline router i have not tested yet.Only one person in another Forum tested it and for him it works.
I have found maybe another solution, there is a tool outside (tftpd32/64) that can make youre laptop act as an dhcp server without Router, maybe this works so you don t nee additional Router
Homepage with Infos for tftpd
http://philippe.jounin.net/tftpd32.html
Just checking
.....i thought that is what you was talking i can help you.....however i need teamviewer access...also you need my software
RE: How to disable parallel programming mode in Ista/P (Icom) - bimmer71 - 04-03-2016
Unsure of what exactly you trying to do , yopu can program any cay, just set staic ip on lan card, and icom ! I have done many this way !
RE: How to disable parallel programming mode in Ista/P (Icom) - winter - 04-03-2016
(04-03-2016, 04:14 AM)bimmer71 Wrote: Unsure of what exactly you trying to do , yopu can program any cay, just set staic ip on lan card, and icom ! I have done many this way !
Dear:
From BMW F-series LCI launched,it removed the ZGM from MOST network and main control module of MOST was changed to NBT,so you can't programming MOST modules because IP assign problem.
Do you sure set static IP can sole this issue?and how to do?thx in adcance.
Who can sure followed combination will solve above MOST programming?
1.Esys>Icom>deactivate parallel programming mode>NBT and all other modules work.
2.Esys>Eth>NBT all other modules work
note:
What is "parrallel programming mode"?and How to deactive it?
and "Esys>Eth>"means Esys+ENET cable?if yes,I tried several times,this combination couldn't programming MOST modules but others network were ok.
thx in advance.
winter