BMW Motorcycles ISTA/P ignition problem. - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Car Technology Motorbikes Forums (https://cartechnology.co.uk/forumdisplay.php?fid=23) +--- Forum: Motorbikes Problems & General Discussions (https://cartechnology.co.uk/forumdisplay.php?fid=37) +--- Thread: BMW Motorcycles ISTA/P ignition problem. (/showthread.php?tid=7318) Pages:
1
2
|
BMW Motorcycles ISTA/P ignition problem. - Czozen - 23-05-2015 Hi, I have ICOM D for BMW Motorcycles, but i have one problem with it. Does anyone know why it do not recognise Ignition Switch position (kl 15 in ISTA/P)? I had 3 BMW motorcycles and it wasn't work I have this one: RE: BMW Motorcycles ISTA/P ignition problem. - kiranabc - 23-05-2015 Dear Friend, did you check the lay out from the pin? best regards RE: BMW Motorcycles ISTA/P ignition problem. - kostia - 28-05-2015 I hadsimilar problem - wrong pinout - need to make jumper between PIN 8 and PIN16 RE: BMW Motorcycles ISTA/P ignition problem. - Czozen - 01-06-2015 Kostia, do You have any picture how to make it? i can't disassemble my obd socket (glued). RE: BMW Motorcycles ISTA/P ignition problem. - epsodus - 02-06-2015 Hi, here is the china Varinate and a good Picture for a IcomD Cabele. This Cable works on K-Line. For CanBus is a other Interface with Electronic. Epsodus Hi, sorry, here is the good Cable. RE: BMW Motorcycles ISTA/P ignition problem. - Czozen - 09-06-2015 Epsodus, OK, so i have to make jumper between PIN 1 and PIN 16 with switch, to turn on and off ignition manually? kostia, PIN 16 is BAT+12V are You sure to make a jumper between PIN 8 (K-Line 2 (ABS)) and PIN 16?? RE: BMW Motorcycles ISTA/P ignition problem. - epsodus - 13-06-2015 Hi, have you on the Motorcicle a CanBus or Kline ? I have the same cable, is not work on Motorcicle with Kline. I have a new cable with the pinout from picture, this work on kline. For Canbus i have a new Cable with electronic in the Case, is work on Kline and Canbus. Hi, sorry, ignition manually is not work and coms from Icom. Hi, here is a Cable from China. (09-06-2015, 12:59 PM)Czozen Wrote: Epsodus, OK, so i have to make jumper between PIN 1 and PIN 16 with switch, to turn on and off ignition manually? RE: BMW Motorcycles ISTA/P ignition problem. - epsodus - 14-06-2015 Hi, i have bought a new Interface for my Motorcycle. This is for all BMW Motorcycle and is for Kline and DcanBus. Works with Esys, IstaD, IstaP and Rheingold. The Interfacename is IstaFighter. I have payed 198,00 Euro. RE: BMW Motorcycles ISTA/P ignition problem. - jaramillo - 29-10-2015 Hi guys, Could anyone tell me where I can buy an ICOM D without the KL15 problem? Thanks in advace, RE: BMW Motorcycles ISTA/P ignition problem. - jaramillo - 03-11-2015 Hi guys, Im a little bit confused about this interface: I have found 2 kinds o intefaces browsing on the web, which one is the best, which are the differences between those? Thanks in advance |