+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10)
+--- Thread: Peugeot 307 dashboard pinout (/showthread.php?tid=81825)
Peugeot 307 dashboard pinout - dani3lxxl - 03-08-2023
Hi all,
What is pinout for this cluster?? Need only for turn on cluster...
Model is
SAGEM 21651870-3
P9654485280 A01
JCAE-CMB-T5C3-CEM00
Ok jack have only 12 wires connected (space for pins 5/6/7/11/12/14 was empty)
The cluster is from Peugeot 307 1.6 hdi from 2006
RE: Peugeot 307 dashboard pinout - al70 - 03-08-2023
I think it's the brown wire, pin16 +, check with multimeter on harness side for voltage when you switch on ignition
RE: Peugeot 307 dashboard pinout - liviu2004 - 03-08-2023
Fuse supply could be pin 6 and minus could be pin 16. But its difficult to check wiring diagrams without an rpo number.
Communication lines seem to be at pins 3 and 5 with BSI.
RE: Peugeot 307 dashboard pinout - tpetrov - 03-08-2023
Pin 8 GND pin 9 positive. But this dash go on from VAN not with plus from terminal 15.
RE: Peugeot 307 dashboard pinout - dani3lxxl - 03-08-2023
(03-08-2023, 09:53 AM)tpetrov Wrote: Pin 8 GND pin 9 positive. But this dash go on from VAN not with plus from terminal 15.
No need 2 positive??
RE: Peugeot 307 dashboard pinout - tpetrov - 03-08-2023
(03-08-2023, 09:56 AM)dani3lxxl Wrote:No. It's start on from VAN bus from BSI module(03-08-2023, 09:53 AM)tpetrov Wrote: Pin 8 GND pin 9 positive. But this dash go on from VAN not with plus from terminal 15.
No need 2 positive??
RE: Peugeot 307 dashboard pinout - dani3lxxl - 03-08-2023
(03-08-2023, 09:53 AM)tpetrov Wrote: Pin 8 GND pin 9 positive. But this dash go on from VAN not with plus from terminal 15.No work with this 2 wire....8 gnd and 9 positive
RE: Peugeot 307 dashboard pinout - tpetrov - 03-08-2023
(03-08-2023, 10:14 AM)dani3lxxl Wrote:My friend, did you understand what I wrote to you?(03-08-2023, 09:53 AM)tpetrov Wrote: Pin 8 GND pin 9 positive. But this dash go on from VAN not with plus from terminal 15.No work with this 2 wire....8 gnd and 9 positive
I said that these are the power supplies, but in order for the dashboard to light up, you need a signal on the VAN bus from BSI module.
How can I explain it to you more clearly?
RE: Peugeot 307 dashboard pinout - liviu2004 - 03-08-2023
tpetrov says wake up signal comes from comms with BSI. If you don’t have bsi you cannot easily turn on this dash.