Calibrate consumption on dashboard passat b5.5 - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: Calibrate consumption on dashboard passat b5.5 (/showthread.php?tid=8435) Pages:
1
2
|
Calibrate consumption on dashboard passat b5.5 - dachasrb - 26-06-2015 Hello can someone help me to calibrate dashboard on passat b5.5 awx motor ,i think that my dashboard dont read real consumption.I put vagcom and consumtion on vagcom is not same on dashboard.What software i need and interfeys. Passat 1.9tdi ,2002,96kw,awx motor BOSCH EDC 15 P 29F400 38906019ER 1.9l R4 EDC WVWZZZ3BZ2P2.. 1037362704 0281010704 Flash:29F400BT Thanks I try to put new map but the consumption is same,on idle is minimum 1.2l/h.I set time belt,replaced maf,injectors is ok. RE: Calibrate consumption on dashboard passat b5.5 - antenor - 27-06-2015 (26-06-2015, 13:44 PM)dachasrb Wrote: Hello can someone help me to calibrate dashboard on passat b5.5 awx motor ,i think that my dashboard dont read real consumption.I put vagcom and consumtion on vagcom is not same on dashboard.What software i need and interfeys. You change the km? This information is in the same EEPROM as km. I think ... RE: Calibrate consumption on dashboard passat b5.5 - dob12 - 29-06-2015 (27-06-2015, 13:37 PM)antenor Wrote: This information is in the same EEPROM as km. you're right You can set this up in adaptations, I do not remember which channel only, but if you use VCDS,there are hints. You can also manually by editing EEPROM. give the number of of the dashboard RE: Calibrate consumption on dashboard passat b5.5 - dachasrb - 29-06-2015 Can i read this number with vcds or i must take off dashboard.I try with vcds i found some post on internet but i dont have canal3 in instruments17-adaptation to change consumption. Thanks for help RE: Calibrate consumption on dashboard passat b5.5 - dob12 - 29-06-2015 (29-06-2015, 18:50 PM)dachasrb Wrote: Can i read this number with vcds or i must take off dashboard Yes you can read this number with vcds I marked the photo where there is a given number RE: Calibrate consumption on dashboard passat b5.5 - dachasrb - 30-06-2015 Here is picture from vcds thanks for help RE: Calibrate consumption on dashboard passat b5.5 - dob12 - 30-06-2015 You can read eprom by OBD, Use cable KKL and VAG eprom programer and 1.19g or Vag tacho or .k can commander. and open content in a hex editor. Fuel consumption information is in the offset 145. Default value is 64 here you can change very important before any modification save the read content. Good luck RE: Calibrate consumption on dashboard passat b5.5 - dachasrb - 01-07-2015 I do read eprom and i get this picture.Can i only change this number to lowest and save ,or what to do. Thanks for real help i am beginner and thanks again. RE: Calibrate consumption on dashboard passat b5.5 - dob12 - 01-07-2015 (01-07-2015, 16:14 PM)dachasrb Wrote: I do read eprom and i get this picture.Can i only change this number to lowest and save ,or what to do..... yes of course, but first save the original dump without change to disk, And now you can change this value as you like and select Write eeprom, after writing EEPROM you are going to VDO and choose Reset this is all remember to power the car was above 12 V during this operation if ever something went wrong you will have a good a dump if you reduced the value,combustion will be less and when raised combustion will be higher. changing to 32 fis will show lower fuel consumption by half RE: Calibrate consumption on dashboard passat b5.5 - dachasrb - 02-07-2015 I put 54 and now i have consumption lover,nov i need to calibrate my consumption with full tank,thanks very much. Thanks again |