Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Set up tool 32 to work with F-Series car
26-08-2023, 20:25 PM,
Post: #1
|
|||
|
|||
Set up tool 32 to work with F-Series car
How do you set up tool 32 to work with F-Series car? i have a cd stuck in an NBT unit on bench
|
|||
27-08-2023, 03:10 AM,
Post: #2
|
|||
|
|||
RE: Eject CD/DVD in NBT/EVO
or it is possible with ISTA
|
|||
27-08-2023, 14:40 PM,
Post: #3
|
|||
|
|||
RE: Eject CD/DVD in NBT/EVO
Ok so i finally got Ediabas Tool32 to connect with F10/F11
So i tried to do this by choosing file, open up Nbt.prg choose in jobs steueren_routine Arguments For steueren_routine choose STEUEREN_EMERGENCY_EJECT Run Job, got this error: EDIABAS Error 13 : IFH-0003: DATATRANSMISSION TO INTERFACE DISTURBED Choose to run Tool32 with admin rights and got this error: Argument WERT[1] missing. Argument table='ARG_0xA007_R'. Argument='ARG_DRIVE'. And that is how far i have gotten now, could anyone point me in the right direction here? Screenshot of Tool32 attached. |
|||
27-08-2023, 15:30 PM,
Post: #4
|
|||
|
|||
RE: Eject CD/DVD in NBT/EVO
(27-08-2023, 14:40 PM)Haug530d Wrote: Ok so i finally got Ediabas Tool32 to connect with F10/F11try '1' in red field |
|||
27-08-2023, 17:07 PM,
(This post was last modified: 27-08-2023, 17:28 PM by Haug530d.)
Post: #5
|
|||
|
|||
RE: Eject CD/DVD in NBT/EVO
(27-08-2023, 15:30 PM)Vadim AA Wrote:(27-08-2023, 14:40 PM)Haug530d Wrote: Ok so i finally got Ediabas Tool32 to connect with F10/F11try '1' in red field That gave me ERROR_ECU_REQUEST_OUT_OF_RANGE Anyway, sorted it with physically removing the CD. The CD was by the way "Kuult" "mehr als Zuvor" So probably some german or polish guy driving around missing his cd :P |
|||
27-08-2023, 17:36 PM,
Post: #6
|
|||
|
|||
RE: Eject CD/DVD in NBT/EVO
(27-08-2023, 15:30 PM)Vadim AA Wrote:2 - CD(27-08-2023, 14:40 PM)Haug530d Wrote: Ok so i finally got Ediabas Tool32 to connect with F10/F11try '1' in red field 4 - DVD |
|||
27-08-2023, 19:20 PM,
Post: #7
|
|||
|
|||
RE: Set up tool 32 to work with F-Series car
- Tool32:
NBT.prg or NBTEVO.prg JOB STEUERN_ROUTINE ARG;STEUERN_EJECT;STR;04 - Or ssh (169.254.199.119) with command cd-eject or eject-cd (either of these 2 commands, I don't remember exactly - Secure coding (NCD 2.0) fit to FA changed (Typschlussel, Serie, Region...).
- FSC 1AA002 OEM for remove component protection MGU18/21 (only case BDC replace). - ID8.5 (SFA) conversion/ change region map. - Virgin Kafas4, MRR, RAM used. - Mgu patch, fsc custom match to vin, remove CP. - Reset ISN 7DTC, 8HP for F, G serie (include EGS7). - Write ISN MG1/MD1 with remotely. - Carplay/Android Auto MGU with/without ATM (6AE). Skype live:laquangksxd |
|||
02-09-2023, 19:12 PM,
Post: #8
|
|||
|
|||
RE: Set up tool 32 to work with F-Series car
Still having problems with this and it wont let me flash the NBT.
So i physically removed the CD. And then i chose STEUERN_ROUTINE and chose 4 i get JOB_STATUS OKAY, but nothing happens and if i go to STATUS_lesen and run F5 i get JOB_STATUS = ERROR_ARGUMENT JOB_MESSAGE = Argument STATUS[1]='STEUERN_EJECT' not valid. Service '22' not found in Table 'SG_Funktionen' column 'SERVICE'='31'. What could be the problem here? |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content