Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ Crafter won't Start after flash
27-03-2018, 18:28 PM,
Post: #21
|
|||
|
|||
RE: Crafter won't Start after flash
sounds daft but have you tried locking then unlocking the vehicle before you try and start?
i help who i want! when i want to! otherwise dont ask free stuff
72656d617020726f73732068656c707320616c6c20746861742068656c7073206d65 genuine winols check click here |
|||
Reputation: +1 - ROD-BENDERS [+1] | |||
27-03-2018, 18:35 PM,
Post: #22
|
|||
|
|||
RE: Crafter won't Start after flash
(27-03-2018, 18:28 PM)Remap Ross Wrote: sounds daft but have you tried locking then unlocking the vehicle before you try and start? Yes i did this as well. The one thing is i found out now. Even If i change Only one bit. And make chks correction and load in to ecu Even than will not start. Looks wired, as i let it made on two pro's. Calculation Still not start. Now i contact to fgtech italy to Support me. Lets see If they have any cloue for this issue Will keep you updated. |
|||
27-03-2018, 18:38 PM,
(This post was last modified: 27-03-2018, 18:51 PM by rs@chip.)
Post: #23
|
|||
|
|||
RE: Crafter won't Start after flash
yes like ross sayed and maybe power off once for 1.min helped me few times..what diagnostic say after flash?If that coverd try writing by obd and crc will be ok you have oem fgtech which is powerful tool and handle this ecu no problem..only tprot have to be patch in case if active..F.G.support is (zero)
|
|||
27-03-2018, 23:17 PM,
Post: #24
|
|||
|
|||
RE: Crafter won't Start after flash
tc looks correct protocol so i can only assume checksum issue.
i dont or have used fg tech,more alien tech fan tbh i have genuine winols and checksum but i think from what i see it is the tool ecu is hw vers 38 but there's much newer so shouldn't think this is an issue as much newer are supported i see let us know what fg tech say and we can delve deeper i help who i want! when i want to! otherwise dont ask free stuff
72656d617020726f73732068656c707320616c6c20746861742068656c7073206d65 genuine winols check click here |
|||
Reputation: +1 - Diagnostix [+1] | |||
27-03-2018, 23:45 PM,
Post: #25
|
|||
|
|||
RE: Crafter won't Start after flash
FileService Stage 1-2-3
SwirlFlaps,EGR/DPF/NOX/DTC/TVA/ADBLUE/Lambda/Immo ALL OFF etc.. Licensed: WinOLS, (Damos map packs,translate)+ FRT files RESELLER EVC Master: Kess Ktag CMD Ecutek, HPTuners, bFlash SKYPE Zenter Performance WhatsApp +48 884 664 588 |
|||
18-04-2018, 20:32 PM,
(This post was last modified: 18-04-2018, 20:32 PM by T-P-C.)
Post: #26
|
|||
|
|||
RE: Crafter won't Start after flash
Hello all together,
Finally i was able to get this car for run. The issue was caused by the tuningfile it self. After remap from another mate Car just Start in first try. I hope this help someone else. Thanks for your Support as well. Cheers Hello all together, Finally i was able to get this car for run. The issue was caused by the tuningfile it self. After remap from another mate Car just Start in first try. I hope this help someone else. Thanks for your Support as well. Cheers |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content