Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
X-tool suppot/Feedback/backup thread
16-10-2017, 13:27 PM,
Post: #111
|
|||
|
|||
RE: X-tool suppot/Feedback thread
Ford Focus 2014 Read/Write via OBDII-- OK.
|
|||
22-10-2017, 10:56 AM,
Post: #112
|
|||
|
|||
RE: X-tool suppot/Feedback thread
Renault modur not work
read correct but not write some edc for vag group ,exemple vw touareg |
|||
24-10-2017, 17:15 PM,
Post: #113
|
|||
|
|||
RE: X-tool suppot/Feedback thread
Ford courier 2016 small screen works by Kuga 2013-
|
|||
29-10-2017, 08:23 AM,
Post: #114
|
|||
|
|||
RE: X-tool suppot/Feedback thread
Renault scenic 2004 obd ok.
Peugeot 208 dash obd ok. Bsi obd ok. But then old mileage back. Polo 2011 JC. Old mileage back after 5min. Very strange. |
|||
29-10-2017, 09:10 AM,
Post: #115
|
|||
|
|||
RE: X-tool suppot/Feedback thread
WHAT YERS PEUGOUT 208 OBD2
|
|||
29-10-2017, 16:05 PM,
Post: #116
|
|||
|
|||
RE: X-tool suppot/Feedback thread
|
|||
29-10-2017, 16:27 PM,
Post: #117
|
|||
|
|||
RE: X-tool suppot/Feedback thread
I use the xtool pro pad2 i had xtool 100 but be care full .car lots use the obd socket - and + wires for the gps locating devise if they should need to repo .well long story short i burnt my wifi dongle when one had wires crossed so i replaced with better .this is a bad issue in my part of U.S.A. and these gps units will interfere with flashing any ecm .one so bad i could not recover it,a new 600 $ unit to beat all . so now i always check before i hook up my $ machine .factory will not replace a burn part of any unit is what i was told .
|
|||
29-10-2017, 16:32 PM,
Post: #118
|
|||
|
|||
RE: X-tool suppot/Feedback thread
(29-10-2017, 16:27 PM)robertbeam26 Wrote: I use the xtool pro pad2 i had xtool 100 but be care full .car lots use the obd socket - and + wires for the gps locating devise if they should need to repo .well long story short i burnt my wifi dongle when one had wires crossed so i replaced with better .this is a bad issue in my part of U.S.A. and these gps units will interfere with flashing any ecm .one so bad i could not recover it,a new 600 $ unit to beat all . so now i always check before i hook up my $ machine .factory will not replace a burn part of any unit is what i was told . My friend .you're getting a little bit confused we are discussion x-tool that's used for ODOMETER not the chinese tool called xtool pad or so BEST CHIPTUNING SERVICE BY Zenter Performance
Contact Skype: zenter-88 Facebook: https://www.facebook.com/ZenterPerformance -------------------------------------------------------------------------------------------------------------- highest Quality ChiPTuninG Files BY PTF Team https://performance-tuningfiles.com/ POWER BY TECHNOLOGY -------------------------------------------------------------------------------------------------------------- BEST CHIPTUNING SERVICE BY Jurebv Contact Skype: live:jure.coric_1 https://files.tuning-makarska.com/ -------------------------------------------------------------------------------------------------------------- - IMMO/ECU , ODO , AIRBAG , CARRADIO , TESTED SOLUTIONS UNDER MY SOFTWARE In progress TUNING STAGE1/DPF/SCR/EGR/TVA/FLAP/ START STOP OFF Software WHAT'S NEWS ! -Steering Angle Sensor Restore For LEXUS,TOYOTA,SUBARU,MITSUBISHI,VAG -Citroen DS5 Steering lock Renew/Write Code by dumps -Passat CCM Repair corrupted dump succes -VAG ECU SIMOS PCR 2.1 KM WITH CRC CORRECTED ! -IMMO OFF For NISSAN/INIFINITI with HITACHI ECU | CPU SH705X -Dacia Dashboard with Fujitsu MB96F6A6 Change km/Block Synchro Dash-ABS -=[Full WinOLS/ECM Titanium User] =- Remember! dirty hands are a sign of clean money шшш.αήkαbôôτ.Ćô.цk |
|||
07-11-2017, 20:46 PM,
Post: #119
|
|||
|
|||
RE: X-tool suppot/Feedback thread
Next week xtool will get new update for vw mqb flatform. golf7 etc.
|
|||
08-11-2017, 09:20 AM,
Post: #120
|
|||
|
|||
RE: X-tool suppot/Feedback thread
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
7 Guest(s)
7 Guest(s)
Return to TopReturn to Content