[egyclick]

Thank you Buzzard, I did disconnect two sockets but only one of the error dissapeard:
"049921 - Motorsteuergerät
U0301 - 003 - Software incompatible"

the other one still shows up:

"049921 - Motorsteuergerät
U0301 - 002 - Software incompatible"

there are 2 sockets for 3 sensors, I don't see other socket that can be disconnected and only solution I guess is to remove the fault from error


there are 2

Hello, I made dpf off for this car using ASC Equipments software and I still get an error

049921 - Motorsteuergerät
U0301 - 002 - Software incompatible

can you please remove it,

thank you very much!

Disconnect 3 sensors on dpf

Sent from my SM-N910F using Tapatalk

[ROD-BENDERS]

Hello,
Guys,need P2413 dtc off,DENSO 4D56 ecu.

Thanks

Post up an untouched ori file for egr removal, this one has had sticky fingers inside

---

Hello, I made dpf off for this car using ASC Equipments software and I still get an error

049921 - Motorsteuergerät
U0301 - 002 - Software incompatible

can you please remove it,

thank you very much!

Egy your checksum was wrong in the file you posted, here is corrected

[sepica]

Hello,
Guys,need P2413 dtc off,DENSO 4D56 ecu.

Thanks

Post up an untouched ori file for egr removal, this one has had sticky fingers inside

---

Hello, I made dpf off for this car using ASC Equipments software and I still get an error

049921 - Motorsteuergerät
U0301 - 002 - Software incompatible

can you please remove it,

thank you very much!

Egy your checksum was wrong in the file you posted, here is corrected

Thanks for your atention.
This file are original,ktag boot mode.
Br.

[ROD-BENDERS]

Sepica although this ecu is fully supported by my software, it comes up with an error saying "there are strings missing from the file" unable to continue.

[Bonkiboy]

Hi
Can you remove dtc P2025 ??
Mercedes Viano 2004 220cdi EDC16c2

[ROD-BENDERS]

Hi
Can you remove dtc P2025 ??
Mercedes Viano 2004 220cdi EDC16c2

Sorry my software not support EDC16C2

[mike_service]

Hi
here you have have "home made" P2025 off file !
check Pm for pass

[egyclick]

Hello, I need your help with this one EDC17C06, the car had dpf off and I only made EGR off with ASC Equipments program, only issue is that the error for EGR returns as shown in the picture '4501' it's the 'equivalent of 'P0401' if that helps you find it.

Although I have paid subscription to ASC their solutions don't seem 100% tested, on diagnosis I can see EGR duty cycle at 4% when idle but while revving the car over 3000rpm it sometimes changes for couple of seconds to 60% while returning to idle so I'm not certain egr is fully disabled but hope the fault code can be removed.

Thank you big time!

[mike_service]

Hi
your ASC software are made incorrect egr off !
upload original file,i will disable egr and dtc related to egr !

[ROD-BENDERS]

Hello, I need your help with this one EDC17C06, the car had dpf off and I only made EGR off with ASC Equipments program, only issue is that the error for EGR returns as shown in the picture '4501' it's the 'equivalent of 'P0401' if that helps you find it.

Although I have paid subscription to ASC their solutions don't seem 100% tested, on diagnosis I can see EGR duty cycle at 4% when idle but while revving the car over 3000rpm it sometimes changes for couple of seconds to 60% while returning to idle so I'm not certain egr is fully disabled but hope the fault code can be removed.

Thank you big time!

Egyclick

Here are 2 files.

I have run your file through my genuine ASC programs, and your egr was successfully removed without issue maps off dtc's deleted.

Then I tried to run it through the dpf remover, and the program clearly showed that the DPF is not fully removed by your software but it could not proceed with a full removal because DPF strings are missing no doubt removed by your other soft.
I cannot do anything more without having your original file.

I made 2 files for you; in the second file I also removed the dtc P0401 that you mentioned.

Your file is clearly labelled "swiftec" which is not ASC. The modified ASC program being offered elsewhere works well on some ecu, but does not work anywhere near as well as the genuine soft, the same is true about almost all modified softwares.