[raffy haddad]

Hello first prepare dealer key with fvdi and you should connect the tag
Programmer to interface put key in prog antenna prepare
Then learn key

[adel.nooh]

I try prepare dealer key 5 times with no success.
I use 2 raw 48 transponder generated to tp23 one time by handy baby and one time by fvdi itself (perform tp23).
Got security code and 6 bytes of cs.
I fix the key programmer of fvdi close to ignition switch (immo ring antenna) and turn car on by putting the key which has the 48 transponder in the miiddle of key programmer just like the picture in fvdi application.
I press prepare dealer key and try to get the 7th byte automatically.
It start to attempt to get it from 0 to 255 trials .
5 times i do that till the end with the same error message (Finished without finding the 7 byte. Propabily the 6 bytes of cs are wrong or the used transponder is invalud (wrong type or with damaged data) )

What do u think guys ?
Is the transponder or i do something wrong?

[raffy haddad]

Hi read eeprom in confort module to get the cs all
Your case is all key lost ?

[adel.nooh]

Hi read eeprom in confort module to get the cs all
Your case is all key lost ?

I am confused now.
Does the dashboard cluster (micronas and 24c32 EEPROM) has the immo data or the comfort control module(CCM EEPROM) ?
What is the type of EEPROM in ccm ? Normal 8 pins or .... ?

[raffy haddad]

Hi i think 95320
Read it and try to get cs 7th bytes with fvdi tag key or post here and for sure some one will help you
When you press thanks and reputation buttons
Then you put the 7th bytes in fvdi and make delear key and then learn key
If all that fail put comfort dump in tag prog and make transponder
Regards

[adel.nooh]

I didnt find any article about immo data in the comfort module of vw golf V ... only for passat it exist in the comfort module.
Instead i found that i can get the 7th byte with carprog
http://codecard.eu/golf5-vdd-vd1-passat-..._2356.html

I did it yesterday and i got the whole cs 7 bytes, login codes, keys ids, vin and odometer.
I success to change km odometer.
I tried fvdi and it can find the 7th byte now... i did dealer key : OK
did Learn step :OK
Unfortunately the word SAFE in screen it keep appearing and all keys are not working.
It seems the immo data cant be changed due to SAFE mode.

ANY SUGGESTIONS ??????

---

By the way i tried to read the engine ecu (Bosch) i think it is MED9.1 to do immo off without success.
It keep saying wait 10 min or turn off then on the key.

[raffy haddad]

Hi
Did you make the steps that on carprog
Instruction
Read eeprom and save fill lines as describe
And then you can do what you want
Another way
When you open fvdi on vw
Put manually in the up left the securite code
And choose key number 1 and program it of course after putting the cs in new key
And when you program first key turn ignition off then on and start the car
Try and report

[adel.nooh]

Hi
Did you make the steps that on carprog
Instruction
Read eeprom and save fill lines as describe
And then you can do what you want
Another way
When you open fvdi on vw
Put manually in the up left the securite code
And choose key number 1 and program it of course after putting the cs in new key
And when you program first key turn ignition off then on and start the car
Try and report

I do just like u said .... but SAFE word keep appearing and number of key counts is 2 and never change either i do 1 key or 2 keys.
Like there is no update to immo data (blocked).
I will try again.

[raffy haddad]

Hi
You mentioned that you adjust km
Put back oroginal file and try
It might when you adjust km something went wrong
Regards

[adel.nooh]

Hi
You mentioned that you adjust km
Put back oroginal file and try
It might when you adjust km something went wrong
Regards

I changed km many times via obd and c1 cable to dashboard directly.
But immo data is fixed not changed at all.
I believe there is a problem in engine ecu or ignition switch put the immo in this safe mode.
Final thing i will take out the engine ecu, read its EEPROM and try to make immo off.