Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
DIGIPROG 3 user help thread !
09-10-2015, 18:47 PM,
Post: #211
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(07-10-2015, 19:38 PM)arm3 Wrote: Hello there. Anyone have tested you need to change dash,it is 35080, there is soldering points to digi manual and if you wont full job you must do ews and lcm. |
|||
10-10-2015, 17:20 PM,
Post: #212
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Hi All,
Does anybody have a digiprog 3 with 4.94?, can you please check if it can control a VW passat with a B7 platform (2011/2012). I saw that in the old (v4.88) the B6 is mentioned in the drop down menu, but apparantly nobody can tell me if the B7 is suported in the new software version. Thkx in advance for looking. Regards W |
|||
10-10-2015, 21:23 PM,
Post: #213
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Yes it works.
but B7 is not listed. you need to go to B6 - diag -2012 or B6 - diag 2012- if not work try T5 or amarok. |
|||
10-10-2015, 22:47 PM,
Post: #214
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
|
|||
11-10-2015, 21:50 PM,
Post: #215
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Hi please could someone help I have a vauxhall zafira b 61 plate 1.7cdti could someone run how to use digiprog 3 on it I would really appreciate your help thanks.
|
|||
14-10-2015, 12:09 PM,
Post: #216
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
The best version is v4.88
Because i work to audi A1 After updat V4.94 audi A1 is not working bmw opel dashboard inside chips 35080 Digiprog i can read only Digiprog i can not erase cheap 35080 For change data buy special programmer for erase chips 35080 Or buy new chips 35080 AFTER digiprog i write chips |
|||
14-10-2015, 12:20 PM,
Post: #217
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Did you try the same car or a different audi a1?
|
|||
14-10-2015, 22:22 PM,
Post: #218
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
|
|||
15-10-2015, 11:30 AM,
Post: #219
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Hi iam a newbie
i have the digiprog 3 v4.94 i like to change the milleage on renault scenic 2000 1,9 dci but i cant find manual or other to show me how to do i hope anybody can help me the backside of the tacho sagem x64 std eu 21650688-1 a v5.01 barcode P7700427896 A i hope you can help me |
|||
21-10-2015, 04:31 AM,
Post: #220
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Put a picture with dash here
100%work solution DPF,EGR,FLAPS,DTC....etc
Genuine WinOLS user dont ask for free files |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
10 Guest(s)
10 Guest(s)
Return to TopReturn to Content