[mjuhl2003]

Hi All

I have updated a lot of cars with ISTA-D and have never had any problems. I use genuen Icom Next and Org. BMW PSU

However I yesterday I updated an F25 and while programming the CIC after 30min a warning turned up on the screen saying somthing like this.

"Warning - Programming session Active on the...."

And I could chose OK - Everything was fine - Programming still running

Then again after 30 min. the same warning came up??


Has anyone seen that before?
Or is something wrong in my install?

I run ISTA-D Standalone

This is from the LOGFILE

2018-01-14 12:03:07 INFO [T] ISTA: [22] InteractionController.RegisterInteractionModel() - A 'InteractionMessageModel' was registered.
2018-01-14 12:05:01 ERROR [T] ISTA: [30] InteractionController.RegisterInteraction - failed with exception: System.ArgumentException: Model is already registered.
at BMW.Rheingold.CoreFramework.Interaction.InteractionController.RegisterInteractionModel(InteractionModel model)
at BMW.Rheingold.CoreFramework.Interaction.InteractionController.RegisterInteraction(InteractionModel model)
2018-01-14 12:05:01 INFO [T] ISTA: [30] VehicleProgrammingProhibitionChecker.ShowMessage() - Programming prohibition occured. Following warningmessage thrown.
2018-01-14 12:05:01 INFO [T] ISTA: [30] VehicleProgrammingProhibitionChecker.ShowMessage() - Important!

An operation with programming is active!

Check the LAN cable and voltage supply and secure them if necessary!

If the instruction is not followed, a programming abort will result.
2018-01-14 12:06:41 INFO [T] ISTA: [1] InteractionRequestModel.OnResponseRecived() - InteractionResponse was set to the model.
2018-01-14 12:06:41 INFO [T] ISTA: [1] InteractionMessageModel.OnResponseRecived() - InteractionButtonResponse was set to the model. Parameter: Button = 'Commit'
2018-01-14 12:06:41 INFO [T] ISTA: [22] VehicleProgrammingProhibitionChecker.ShowMessage() - Programming prohibition occured. Following warningmessage thrown.
2018-01-14 12:06:41 INFO [T] ISTA: [1] InteractionController.DeregisterInteraction() - A 'InteractionMessageModel' was deregistered.
2018-01-14 12:06:41 INFO [T] ISTA: [22] VehicleProgrammingProhibitionChecker.ShowMessage() - Important!

An operation with programming is active!

Check the LAN cable and voltage supply and secure them if necessary!

If the instruction is not followed, a programming abort will result.
2018-01-14 12:31:01 INFO [T] ISTA: [19] InteractionController.RegisterInteractionModel() - A 'InteractionMessageModel' was registered.
2018-01-14 12:31:13 INFO [T] ISTA: [1] InteractionRequestModel.OnResponseRecived() - InteractionResponse was set to the model.
2018-01-14 12:31:13 INFO [T] ISTA: [1] InteractionMessageModel.OnResponseRecived() - InteractionButtonResponse was set to the model. Parameter: Button = 'Commit'
2018-01-14 12:31:13 INFO [T] ISTA: [19] VehicleProgrammingProhibitionChecker.ShowMessage() - Programming prohibition occured. Following warningmessage thrown.
2018-01-14 12:31:13 INFO [T] ISTA: [1] InteractionController.DeregisterInteraction() - A 'InteractionMessageModel' was deregistered.
2018-01-14 12:31:13 INFO [T] ISTA: [19] VehicleProgrammingProhibitionChecker.ShowMessage() - Important!

An operation with programming is active!

Check the LAN cable and voltage supply and secure them if necessary!

If the instruction is not followed, a programming abort will result.
2018-01-14 12:33:05 INFO [T] ISTA: [26] InteractionController.RegisterInteractionModel() - A 'InteractionMessageModel' was registered.
2018-01-14 12:33:17 INFO [T] ISTA: [1] InteractionRequestModel.OnResponseRecived() - InteractionResponse was set to the model.
2018-01-14 12:33:17 INFO [T] ISTA: [1] InteractionMessageModel.OnResponseRecived() - InteractionButtonResponse was set to the model. Parameter: Button = 'Commit'
2018-01-14 12:33:17 INFO [T] ISTA: [26] VehicleProgrammingProhibitionChecker.ShowMessage() - Programming prohibition occured. Following warningmessage thrown.
2018-01-14 12:33:17 INFO [T] ISTA: [1] InteractionController.DeregisterInteraction() - A 'InteractionMessageModel' was deregistered.
2018-01-14 12:33:17 INFO [T] ISTA: [26] VehicleProgrammingProhibitionChecker.ShowMessage() - Important!

An operation with programming is active!

Check the LAN cable and voltage supply and secure them if necessary!

If the instruction is not followed, a programming abort will result.

Thanks

[SweetBMW]

Bad Network cable maybe?

[mjuhl2003]

I just saw this one from the release notes - I think that is the problem

4.13 ICOM connection fault is displayed during programming
Fault description:
It is possible that a ICOM connection fault will be displayed during programming, especially when
programming the Head Unit High.
Model series affected:
All vehicles.
Measure/workaround:
The message can be ignored.
Fault corrected by:
Currently still open.
Affected application:
ISTA 4