[Clusters]

2003 GMC Sierra no need solder chip use Avalanche OK, HUMMER -2007 should work also and can do hours.

---

Confirmed today, 2004 Silverado Km and Hours adjusted using HUMMER/H2/HUMMER -2007 without soldering chip. This should work on all 2003-2006 GM Truck and SUV like Tahoe, Avalanche, Yukon, Sierra, Silverado and even Escalade. The KM programs within 100Km, desired 185,232 Actual 184,489, but the hours very accurate.

They all use the S95P02 Eeprom 2003-06 full size truck and SUV. Do make a backup of Eeprom first!

[waynestewart123]

Does anyone know if the digiprog 3 is compatable with a suzuki alto? 2011 model?

[Chad69]

New to the forum I have digiprog 3 with all cables

Obd I have tried on corsa 59 plate , ford focus 1999 , corsa 07 plate , a3 Audi 06
But don't connect says error no connection


Can anyone confirm what year cars will work with this device it's 4.88 version thank you

A list of cars it can work on and English manual thanks or something I can learn to use it correctly

[Clusters]

New to the forum I have digiprog 3 with all cables

Obd I have tried on corsa 59 plate , ford focus 1999 , corsa 07 plate , a3 Audi 06
But don't connect says error no connection


Can anyone confirm what year cars will work with this device it's 4.88 version thank you

A list of cars it can work on and English manual thanks or something I can learn to use it correctly

I had problems with OBD cable too, opened it up and soldering of the wires to the board very bad, one touching another, but I haven't tried since.

Edit: I used it yesterday and it communicates now on a vehicle that previously didn't, so check the internal wiring of the OBD2 plug.

Follow the directions in manual for different cars, Google translate works well if all you have is German manuals. List of cars is out there all over the net.

Hope some of this helps

By the way, anyone have pinouts for the OBD2 connector, from db25 connector to the board inside OBD2 plug? Much appreciated.

[Fraz]

Has anyone managed to do a C Class W204? Did you have to install CAN or do anything special? Or can it just be done by OBD?

[Avtoprofi]

Has anyone managed to do a C Class W204? Did you have to install CAN or do anything special? Or can it just be done by OBD?

Mercedes w 204 2009 year

W204 © – EZS - DIAG ok , 2 min
W204 © - ASSYST - DIAG ok, 15 min

If you do EZS BY OBD its change the km in ezs and the tacho!

[666]

Hi all,

A. Do we have a risk for EZS? Can Digiprog 3 flashes the ezs to 1.6million km? Can that happen? Yes/No?

B. Do i need to start the engine when i update EZS and Tacho (Dash)? Yes/NO!!!

C. If i good understand, if i flash EZS only, tacho will be updated also, so don't need to update dash (Tacho) after update EZS? Correct?

Thanks 4 help
Kinds Regards
666

[Fraz]

Hi guys,

can anyone tell me if i can just do the Peugeot 207 2007 speedo or do i have to do the BSI too?

Also do you have to remove the eeprom in the dash or can you do it without removing it?

Thanks,

[vaidisvaidis]

Dash + bsi,remove eprom

[canones76]

Hello very good i'm New Here I appreciate that this this forum.
my question is I want to make a renault espace 2006 with gps and not in the manual, only the horn 2003 with the cable 47 and when I look in the digiprog v4.88 I get the cable 42 and not in the manual .
anyone can help me would be helpful or someone already did
Thanks in advance
a greeting