Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

IHKA3 retrofit, 3AG stopped working
28-04-2022, 07:39 AM,
Post: #1
IHKA3 retrofit, 3AG stopped working
Hi everyone,

Basically I want to retrofit IHKA3 on my 2012 car. Removed the old one and in with the new one 6820235.
Because it got late last evening, I didn`t do the wirings/codings, so today the IHKA control panel, radio controls, climate controls wasn`t working, as expected.
Got at work without climate control at all, reversed the car and reverse camera is black. Is this because of the new IHKA? 
Is reverse camera connected to IHKA in any way?
I simply don`t want to do the wirings and find out the camera will not work with the IHKA3.
Car in question F31 with VIN: F786504

Thanks in advance.

[Image: OxNUyuy.jpg]
Quote this message in a reply
28-04-2022, 08:01 AM,
Post: #2
RE: IHKA3 retrofit, 3AG stopped working
which car is this
Quote this message in a reply
28-04-2022, 08:11 AM,
Post: #3
RE: IHKA3 retrofit, 3AG stopped working
(28-04-2022, 08:01 AM)maxwell4321 Wrote:  which car is this

F31, F786504 VIN

[Image: OxNUyuy.jpg]
Quote this message in a reply
28-04-2022, 08:50 AM,
Post: #4
RE: IHKA3 retrofit, 3AG stopped working
There is no direct connection between reverse camera and IHKA, however it is possible that the new IHKA module is killing signals on the LINBUS which the camera needs. You need to correct all the wiring to accommodate the new IHKA in the first instance.
Just to prove a point plug in the original IHKA and see if the camera works.
Quote this message in a reply
[+] 1 user says Thank You to maxwell4321 for this post
28-04-2022, 09:01 AM, (This post was last modified: 28-04-2022, 09:02 AM by XuLeTZ.)
Post: #5
RE: IHKA3 retrofit, 3AG stopped working
(28-04-2022, 08:50 AM)maxwell4321 Wrote:  There is no direct connection between reverse camera and IHKA, however it is possible that the new IHKA module is killing signals on the LINBUS which the camera needs. You need to correct all the wiring to accommodate the new IHKA in the first instance.
Just to prove a point plug in the original IHKA and see if the camera works.

I think will try first the wiring this afternoon smile Wiring is easier for me than taking the glovebox off again and plug the old IHKA.
Thank you once again.

(28-04-2022, 08:50 AM)maxwell4321 Wrote:  There is no direct connection between reverse camera and IHKA, however it is possible that the new IHKA module is killing signals on the LINBUS which the camera needs. You need to correct all the wiring to accommodate the new IHKA in the first instance.
Just to prove a point plug in the original IHKA and see if the camera works.

Only need 2 wires for new IHKA3, from KCAN to KCAN2 in FEM and it should be good. Will kick in ISTA as well and see what`s going on in the car's mind.

[Image: OxNUyuy.jpg]
Quote this message in a reply
[+] 1 user says Thank You to XuLeTZ for this post
28-04-2022, 09:41 AM,
Post: #6
RE: IHKA3 retrofit, 3AG stopped working
IHKA -> KCAN_H Pin 22 to Pin 34 FEM A173*7B
IHKA -> KCAN_L Pin 23 to Pin 33 FEM A173*7B

IHKA3 -> KCAN2_H Pin 22 to Pin 10 FEM A173*10B
IHKA3 -> KCAN2_L Pin 23 to Pin 11 FEM A173*10B
If you can't see IHKA3 in esys then you will need write manually and code it

Successfully retrofit on BMW F30 335xi 248,302,3AG,430,5AG,5AS,6NS,8TH,IHKA3
Quote this message in a reply
[+] 2 users say Thank You to Siki78 for this post
28-04-2022, 10:44 AM,
Post: #7
RE: IHKA3 retrofit, 3AG stopped working
(28-04-2022, 09:41 AM)Siki78 Wrote:  IHKA -> KCAN_H Pin 22 to Pin 34 FEM A173*7B
IHKA -> KCAN_L Pin 23 to Pin 33 FEM A173*7B

IHKA3 -> KCAN2_H Pin 22 to Pin 10 FEM A173*10B
IHKA3 -> KCAN2_L Pin 23 to Pin 11 FEM A173*10B
If you can't see IHKA3 in esys then you will need write manually and code it

Thanks, had this info.
Will try later today to tap the wires 33 and 34 from A173*7B to 10 and 11 in A173*10B.
Thinking of just disconnecting the pins from old IHKA and do a bridge to the KCAN2 wires. Wrap them up and make a jumper wire that goes from cable to cable just in case I need to revert them back smile 
Thanks

[Image: OxNUyuy.jpg]
Quote this message in a reply
28-04-2022, 15:31 PM,
Post: #8
RE: IHKA3 retrofit, 3AG stopped working
All sorted after wiring the IHKA3 to KCAN2.
Deleted the IHKA ecu from SVT, injected new CAFD and Code it.
Reverse camera also working now.
Thanks everyone.


Attached Files Thumbnail(s)
   

[Image: OxNUyuy.jpg]
Quote this message in a reply
[+] 2 users say Thank You to XuLeTZ for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
  BMW F31 acc retrofit help Pedrom92 10 1,366 Yesterday, 22:56 PM
Last Post: azwgh
XZBMW G30 Entrynav2 - rear camera retrofit problem Krysiaman 19 1,341 Yesterday, 20:39 PM
Last Post: Node
XZBMW Entrynav2 to NBT EVO retrofit, no rear view camera image jce777 2 50 Yesterday, 20:31 PM
Last Post: jce777
  F20 cruise control retrofit maninblack 5 135 22-05-2024, 18:09 PM
Last Post: qbek90
XZBMW BMW e87 LCI hralights retrofit problem XeoN 0 29 21-05-2024, 21:17 PM
Last Post: XeoN
ZBentley Tool to use to cut leather dashboard for hud retrofit Fx82 3 315 19-05-2024, 15:29 PM
Last Post: Fx82
XZBMW F01 LCi Xenon Headlight Retrofit mcrussell 0 57 16-05-2024, 11:57 AM
Last Post: mcrussell
  retrofit USB BMW E63 Jalami 9 260 15-05-2024, 17:39 PM
Last Post: The CaT
XZBMW Retrofit comfort access BMW f26 santopalermo 13 420 14-05-2024, 12:25 PM
Last Post: ruben_17non
  EDC17CP09 Working hours reset MBENZTECH 1 110 14-05-2024, 06:44 AM
Last Post: foxportal

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content