Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
How to use DiagBox 7.62
17-04-2016, 14:29 PM,
Post: #1
|
|||
|
|||
How to use DiagBox 7.62
Hi,
I installed DiagBox 7.62 in a VM running Win7 32bits (don't know if earlier versions are better, as some people says 7.62 is the best version). The software runs fine but I don't know if it works with my car. What should I do next ? (should I buy a special cable, install something else, ....) Thank you for your help |
|||
17-04-2016, 18:01 PM,
Post: #2
|
|||
|
|||
RE: How to use DiagBox 7.62
You must have interface, Lexia is name
|
|||
17-04-2016, 20:36 PM,
Post: #3
|
|||
|
|||
RE: How to use DiagBox 7.62
You need psa evolution interface
|
|||
18-04-2016, 09:05 AM,
Post: #4
|
|||
|
|||
RE: How to use DiagBox 7.62
Thank you for your answers
But what are PSA Evolution Interface and Lexia ? I searched on Google but it seems PSA Evolution interface is something I should buy whereas Lexia is another software |
|||
18-04-2016, 10:02 AM,
Post: #5
|
|||
|
|||
RE: How to use DiagBox 7.62
You are right.. XS Evolution is the (VCI) device and Lexia is the software.
In the old days, Lexia (for Citroen) and PP2000 (for Peugeot) were stand alone software that you installed individually, but now they are included in the DiagBox package.. So, if you download and install DiagBox 7.62, you would have Lexia v500.68 and PP2000 v600.72 within it.. Upon starting it should flash your "VCI" with firmware version 4.3.3. Later DiagBox releases include newer versions of Lexia and PP2000 and Firmware v4.3.4.. A good example of a (Full Chip) device (including the software): http://www.aliexpress.com/item/2016-Lexi...6e6f028377 Notice no missing components and the 4 legged oscillator chip (like the original), other devices may have missing or bad quality components. With respect to which is the best release, obviously if you have the authentic software, the latest the better. But if you have an oldish car, you don't need any of the bells and whistles for a new car (like configuring a Bluetooth device), then whatever works best... So the answer is, it depends on your car.. By the way, you can do Telecoding on newer releases of DiagBox, you will learn everything you need as you work your way through this jungle of forums, we all had to tread that path.. |
|||
13-06-2016, 18:14 PM,
Post: #6
|
|||
|
|||
RE: How to use DiagBox 7.62
Hi I'm using 7.62 version and I'm trying to make telecode on smeg_plus of citroen c4 picasso 2015). But i have an error: " unable to access authentication server. Try later". Internet is disable...so what i can do? I need to patch diagbox 7.62 with tlcd fix?
Inviato dal mio LG-H850 utilizzando Tapatalk |
|||
13-06-2016, 20:22 PM,
Post: #7
|
|||
|
|||
RE: How to use DiagBox 7.62
I think telecoding smeg_plus was fixed in update version 8.15. You can try later updates.
Correction concerning the configuration values --> SMEG / SMEG+ --> All vehicles check Citroen Service page for more information: http://service.citroen.com/dtt/IFD/AC/documents/en_GB/ |
|||
15-06-2016, 07:35 AM,
Post: #8
|
|||
|
|||
RE: How to use DiagBox 7.62
(13-06-2016, 20:22 PM)Simple Wrote: I think telecoding smeg_plus was fixed in update version 8.15. You can try later updates. Hi, with 7.82 version (8.18) it's possible to make telecode into smeg plus? Or there are still problems? Then using a version higher then 7.62, it's still possible to make manual telecode? |
|||
15-06-2016, 13:54 PM,
Post: #9
|
|||
|
|||
RE: How to use DiagBox 7.62
I cannot verify it (I don't have this functionality), but DiagBox 8.15 is what was reported by some users for telecoding smeg+. You can only take a chance and try!!
You can make manual Telecoding with version higher than 7.62, you just disconnect and hit enter, reconnect and continue.. This was discussed and you will find it in one of the posts on this forum. |
|||
15-06-2016, 17:52 PM,
Post: #10
|
|||
|
|||
RE: How to use DiagBox 7.62
(15-06-2016, 07:35 AM)scoutman Wrote:Hi I've just tried to make telecode with 7.82 version, but into smeg plus I've the same error: unable to access to authentication server...I've the tried to make a telecode into bsi but it doesn't ask to connect internet, telecode start directly but unsuccessful...i need to make same change into diagbox??(13-06-2016, 20:22 PM)Simple Wrote: I think telecoding smeg_plus was fixed in update version 8.15. You can try later updates. Inviato dal mio LG-H850 utilizzando Tapatalk |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
diagbox 9.173 | sharawi | 2 | 172 |
21-04-2024, 14:31 PM Last Post: justdiag |
|
PSA Diagbox VCI Interfaces | alexturbo | 18 | 6,854 |
27-12-2023, 21:45 PM Last Post: apol |
|
DIAGBOX 2021 9.85 FULL INSTALATION | akli | 6 | 2,763 |
26-12-2023, 20:21 PM Last Post: Le-Mans |
|
DIAGBOX online | walczaklu | 10 | 8,706 |
03-12-2023, 12:57 PM Last Post: mattydr67 |
|
DiagBox 7+Updates+Firmware+Drivers+Tools (Magnet) | Simple | 33 | 35,694 |
22-11-2023, 06:16 AM Last Post: Jeppo |
|
Diagbox 9.129 activation request | dadoa4 | 4 | 2,451 |
09-11-2023, 09:59 AM Last Post: bovhec |
|
diagbox 9.150 | stasi | 5 | 2,284 |
16-09-2023, 19:41 PM Last Post: stasi |
|
DiagBox Language Change | Simple | 16 | 17,475 |
14-09-2023, 10:01 AM Last Post: żarówka |
|
DIAGBOX help needed installing | mars2moon | 4 | 1,054 |
23-07-2023, 18:45 PM Last Post: J415UNNY |
|
Diagbox 9.91 VmWare | gabi2008 | 6 | 4,284 |
23-07-2023, 18:42 PM Last Post: J415UNNY |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content