[fabulous]

Today I tried again.

I have followed every step.
But when I change de Werte from "00" to "01" bij "aktiv" and than save. I see werte is still "00".

When I put it on "night aktiv" then I see Werte going to "01".
I can not change Werte=00 to Werte=01 by aktiv.

When I saved it go back and than I do CODE FDL, close the popup. Close de E-Sys, Close my car and wait 5 minutes.
When I connect E-Sys, read the CAS then I see nothing is changed its same as before orginal state.

Fabulous:
if you don't want a delay in closing, you also need to code this:
CAS->3003 FH MASTER->KMFRT_SCHLIESSEN->Werte=00

Must I put this to "aktiv" ....... " -> aktiv -> Werte=00"?
Must I put this to "night aktiv" ....... " -> night aktiv -> Werte=00"?

Thank you.

This happen to me during coding also make sure the car engine is on and running when coding because if car is not running with ignition on for a while modules go to sleep. What i did i ran ISTA/D and clear all codes from the car if there are any then i try to code again. If you still having problems update the ECU with the latest psdzdata.

To change Werte=00 Values
Go to page 17 of the PDF (Beginners Guide Coding)POST 15b and 16b.

---

Thank you FX82. Will try it again.

Do you know the following ?

Fabulous wrote:
if you don't want a delay in closing, you also need to code this:
CAS->3003 FH MASTER->KMFRT_SCHLIESSEN->Werte=00

Must I put this to "aktiv" ....... " -> aktiv -> Werte=00"?
Must I put this to "night aktiv" ....... " -> night aktiv -> Werte=00"?

Just change Werte=00 value only


CAS -> 3003 FH MASTER -> KMFRT_SCHLIESSEN
Werte=00 (the default value is Werte=0F)
This results in a much faster folding of the mirrors when comfort closing.
05 for 0.5sec
0A for 1sec
0F for 1.5sec

[BMWLorenz]

I have followed all the steps, finally it is change to werte=01, but when I finished with the "Code FDL" and closed the E-Sys, my mirrors don't working anymore.

I connect again to the car, I see everthing is going to
Night aktiv -> Werte= 01

pls need your help.
------
Factory default are the settings by my car:
FRM -> 3020 -> ASP_BEIKLAPPEN_BEI_KOMFORTSCHLIESSEN -> activ -> Werte=01
CAS -> 3003 -> KOMFORTSCHLIESSUNG_FB -> activ -> Werte=00
CAS -> 3003 -> KOMFORTSCHLIESSUNG_PA -> activ -> Werte=00
CAS -> 3003 -> KMFRT_SCHLIESSEN -> activ -> Werte=00

My Mirrors working by factory defaults fine, but I have a delay.
What I want is when i lock my doors with comfort acces/key that the mirrors automatic also closed without delay.

[fabulous]

I have followed all the steps, finally it is change to werte=01, but when I finished the Code FDL and closed the E-Sys, my mirrors don't working anymore.

I connect again to the car, I see everthing is going to
Night aktiv -> Werte= 01

I don't understand it.

pls need your help.

------
Factory default are the settings by my car:
FRM -> 3020 -> ASP_BEIKLAPPEN_BEI_KOMFORTSCHLIESSEN -> activ -> Werte=01
CAS -> 3003 -> KOMFORTSCHLIESSUNG_FB -> activ -> Werte=00
CAS -> 3003 -> KOMFORTSCHLIESSUNG_PA -> activ -> Werte=00
CAS -> 3003 -> KMFRT_SCHLIESSEN -> activ -> Werte=00

Was there any errors after you complete FDL coding did everything looks like page 15 of PDF STEP 20 AND 21

[BMWLorenz]

After Code FDL, No errors, blinking green.
I see it changes only from activ to nigh activ. The Werte I can't change.

last Monday my car get overall update by the dealer. I have the latest update.

[fabulous]

After Code FDL, No errors, blinking green.
I see it changes only from activ to nigh activ. The Werte I can't change.

last Monday my car get overall update by the dealer. I have the latest update.

Do you have teamViewer on you pc

[BMWLorenz]

I will install Teamviewer,
I have internet connection on my car 4G. I will connect my laptop on my car.

My laptop must be charge 30 minutes because it is now 16%.
I will be on my car 14:45 (Netherlands Time)

[fabulous]

I will install Teamviewer,
I have internet connection on my car 4G. I will connect my laptop on my car.

My laptop must be charge 30 minutes because it is now 16%.
I will be on my car 14:45 (Netherlands Time)

PM me TeamViewer info when ready and run TeamViewer as admin