Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Xentry OpenShell PassThru 09-10-11.2016
24-11-2016, 17:01 PM,
Post: #21
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
(24-11-2016, 16:53 PM)stel_01 Wrote: Hi and thanks for the software much appreciated. do you know how to flash VAS5054 in order to work with xentry?Last Time i Flashed my Interface was when i Installed ODIS 2.7 ..... and to work with Xentry I DID NOT HAVE TO FLASH ANYTHING!!!! To use Xentry with VAG-Interface you need SAEJ2534-1 For VAS 5054A software that includes PassThru software Read first post "3)Install PassThru Software and Drivers, Reboot, configure your PassThru make sure it's working and can be seen/tested and used in Windows " If any of my posts or current one helps then don't forget to press thanks and add a reputation
|
|||
25-11-2016, 06:05 AM,
Post: #22
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
(22-11-2016, 19:04 PM)bibkare Wrote: According these pinouts pin8 is ignition at mercedes while at VW is some "CAN". Can this be true, what type of CAN uses pin 8. Strange. I will connect pin 8 with 1 and see will there be any difference. Could the file that i uploaded "Ignition" have an answer ? [GLOBAL] IGNITION =OFF COMPORT = FREE ;--- FREE or BUSY, FREE is default IGNITION_VOLTAGE = 12.0 ;--- float value with POINT as decimal separator BATTERY_VOLTAGE = 12.5 ;--- float value with POINT as decimal separator If any of my posts or current one helps then don't forget to press thanks and add a reputation
|
|||
25-11-2016, 12:22 PM,
Post: #23
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
I tested and if leave like this "[GLOBAL] IGNITION =OFF " then no connection at all. There is another settings in C:\program file\mercdes-benz\DAS\bin\cal.ini where you can enable or disable passthru device to read voltage. I set value from 1 to 0 and then DAS shows value from global.sim BATTERY_VOLTAGE = 12.5 and if it is value=1 then shows IGNITION_VOLTAGE = 12.0. This was tested on VAS5054 however x-horse MVCI "see" correct voltage but can't connect to all modules for example it coudn't read SAM in ML164 while VAS5054 reads all modules.
|
|||
27-11-2016, 12:16 PM,
Post: #24
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
Hi, is this software support vans to?
|
|||
27-11-2016, 15:45 PM,
Post: #25
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
|
|||
03-12-2016, 09:28 AM,
Post: #26
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
Hi,is this software can do SCN online coding?
|
|||
03-12-2016, 17:19 PM,
Post: #27
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
(03-12-2016, 09:28 AM)61774058 Wrote: Hi,is this software can do SCN online coding?That is an idea of passthru, to be able program new modules and code new modules If any of my posts or current one helps then don't forget to press thanks and add a reputation
|
|||
03-12-2016, 17:34 PM,
Post: #28
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
Todaj tested with DPA5, works better than VAS5054, correct voltage reading and it's 20% faster
|
|||
12-12-2016, 16:19 PM,
Post: #29
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
How install it to work with AVDI?
Sent from One+3 |
|||
12-12-2016, 16:25 PM,
Post: #30
|
|||
|
|||
RE: Xentry OpenShell PassThru 09-10-11.2016
(12-12-2016, 16:19 PM)drovid Wrote: How install it to work with AVDI?Same way as with VAS5054A first you install AVDI Software/drivers then passthru soft/drivers that are provided with AVDI and then Xentry! If you still can not, then contact AVDI for help on installing passthru drivers/software "FVDI" will not going to work, only "AVDI" If any of my posts or current one helps then don't forget to press thanks and add a reputation
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content