[pica14]

Hello
I need flash update zgw in bmw f25 but i have error and the car it is dead in mode transport
I have guide the flash by esys in internet but dont work in my car
I have esys and enet cable whit esys 3.27

Any idea why dont work? O any solution

[Breach]

Hello
I need flash update zgw in bmw f25 but i have error and the car it is dead in mode transport
I have guide the flash by esys in internet but dont work in my car
I have esys and enet cable whit esys 3.27

Any idea why dont work? O any solution

Was just working with someone on this on another forum - couldn't help him out at the end. But it did flash for me with a DHCP server (tftpd64).

To take the car out out of transport mode just VO code any ECU - right-click on the ECU (e.g. something like the audio one) and select code. Do NOT click on Code Defaults - ever.

Here's what worked for me:

e-Sys 3.27.1, tftpd64's DHCP: Ethernet card set to static 169.254.0.1, pool starts at 169.254.0.2, pool size 1024, subnet mask 255.255.0.0, gw 169.254.0.1. Connection by ZGW's IP, swdeploy only. Completed OK, though C207 error when executing SVTsollupdate (which was fixed when I did the full flash -ZGW).

[pica14]

Ok
I have put 4 selc bflash,swdeploy,cddeploy,ibadeploy and you see also swdeploy?

I can obtain error for this selection?

[Breach]

Ok
I have put 4 selc bflash,swdeploy,cddeploy,ibadeploy and you see also swdeploy?

I can obtain error for this selection?

Normally only the swDeploy will be run anyway - this depends on the SVT Target (what i-Step you come from, what your hardware is) and what TAL was generated. Shorty answer - yes. An error is likely with ENET and ZGW

[pica14]

Ok
I have put 4 selc bflash,swdeploy,cddeploy,ibadeploy and you see also swdeploy?

I can obtain error for this selection?

Normally only the swDeploy will be run anyway - this depends on the SVT Target (what i-Step you come from, what your hardware is) and what TAL was generated. Shorty answer - yes. An error is likely with ENET and ZGW

I have from ilevel F025-10-503, now i update car full whit istap F025-15-07-502 but i dont can update zgw because istap tell me change zgw for other ref, because my car it is retrofit cic profesinal navi and now the cruise control dont work because zgw old firmnware

Can i put zgw used whit ref. Tell my ista-p? And reflash the zgw whit ista-p?

Or i update my actual zgw whit new firmnware by esys? But i have error , i read what varios zgw dont can update firmnware by esys

[lagunasec]

Yes, you can replace the ZGW with an used one (try to find one with a newer production date than your car and part number asked by ISTA-P).

[pica14]

Yes, you can replace the ZGW with an used one (try to find one with a newer production date than your car and part number asked by ISTA-P).

Ok i found one by eBay i post result when i Have tested

[ap90500]

What? Replace a ZGW because you can't update it? Send your contact info to me as a private message...Your original zgw will work just fine.

[warhol99]

Help, please...

I try flash ZGW via ICOM with ISTA P...bootloader done ,but then show some error ....now car is dead, ISTA ask me vehicle order


so i try flash ZGW via ENET and ICOM with esys ...same error....TAL,SVT calculated, FA loaded, unchecked switch ecu....connected via GW X.X.X.X:6801 (ENET)

i use dhcp server, esys 3.27.1
   

[leo04]

Turn off MSM update