Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Nissan Idle Air Volume Learn without scantool
26-10-2016, 22:05 PM,
Post: #1
UNissan  Nissan Idle Air Volume Learn without scantool
Accelerator Pedal Released Position Learning
DESCRIPTION
Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position sensor or ECM is disconnected.

OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch ON and wait at least 2 seconds.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON and wait at least 2 seconds.
5. Turn ignition switch OFF and wait at least 10 seconds.

BASIC SERVICE PROCEDURE
2007 Armada

Throttle Valve Closed Position Learning
DESCRIPTION
Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by monitoring the throttle position sensor output signal. It must be performed each time harness connector of electric throttle control actuator or ECM is disconnected.

OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch ON.
3. Turn ignition switch OFF wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.

IDLE AIR VOLUME LEARN (Manually)
1. Perform "Accelerator Pedal Released Position Learning" .
2. Perform "Throttle Valve Closed Position Learning" .
3. Start engine and warm it up to normal operating temperature.
4. Check that all items listed under the topic PREPARATION (previously mentioned) are in
good order.
5. Turn ignition switch OFF and wait at least 10 seconds.
6. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
7. Repeat the following procedure quickly five times within 5 seconds.
a. Fully depress the accelerator pedal.
b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds
until the MIL stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
10. Start engine and let it idle.
Quote this message in a reply
[+] 6 users say Thank You to shadab for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
UInfiniti Looking for Nissan Consult j2534 drovid 5 326 16-03-2024, 15:01 PM
Last Post: domelec
  Nissan Qashqai 2019 need cooding sorin.henea 1 87 04-03-2024, 09:05 AM
Last Post: xxmatixx
  2009 Nissan Sentra Calibration file koziol 0 36 26-02-2024, 16:35 PM
Last Post: koziol
  Nissan Qashqai no cummunicate with ecm , many fault u1000 TKservice 0 45 23-02-2024, 06:59 AM
Last Post: TKservice
UNissan Glow plugs values Nissan x-trail t32 dci bad start AlexM3F80 3 102 23-02-2024, 06:25 AM
Last Post: AlexM3F80
  nissan pickup 2005 new key davito1 0 23 22-02-2024, 17:08 PM
Last Post: davito1
  Nissan Consult III+, V75, Full install, Reprogramming database, Operation manual , Fr sazimam 17 4,663 08-02-2024, 19:26 PM
Last Post: drovid
UNissan Nissan Consult 3 plus V82.50.00 + Pplus V83 + europatch V42.1 predacon 5 1,938 08-02-2024, 19:23 PM
Last Post: drovid
UNissan Nissan Consult 3 + V226 Inc Programming Data simo2k 16 3,221 07-02-2024, 17:03 PM
Last Post: florinyes
ZSeat Nissan 1.5 dci ltujustas 0 74 25-01-2024, 11:04 AM
Last Post: ltujustas

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content