Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Change VIN in ECU with WinKFP possible?
05-12-2016, 15:54 PM,
Post: #1
|
|||
|
|||
Change VIN in ECU with WinKFP possible?
Hi all
I have the following ECU with me from X1 E84 Diesel Bosch nr: 0281016110 BMW nr: 8506438 Can I change VIN number of this ECU with WinKFP? This ECU is from a donor car (which is manual transmission) - I want to install it into an X1 with auto transmission. I need to change VIN before programming / coding with ISTA P - so would it be possible with WinKFP? Thanks Cheers |
|||
05-12-2016, 17:49 PM,
Post: #2
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Yes, if you flash the DME with WinKFP it will change the VIN to the one you type. If not, Tool32 can do it.
However depending on DME, you may not be able to use a second hand DME to another car because of ISN issues. You may also need to code it after flashing. |
|||
05-12-2016, 18:04 PM,
Post: #3
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Yes you can change the VIN with Winkfp,
you also need to change to a correct ZUSB (automatic transmission) If you use a second hand ECU you also need to align the ISN from the used ECU with your CAS, This can't be done with the BMW tools (INPA,NCS,ISTA) etc.. |
|||
05-12-2016, 19:14 PM,
Post: #4
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
|
|||
05-12-2016, 19:54 PM,
(This post was last modified: 05-12-2016, 19:56 PM by Sabreace.)
Post: #5
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Quote:With tool 32 you must enter 18 It's the Checkdigit and Number 18 of your Vin ( Last digit ) Vin change only looks good but ISN must be the same and that's not possible with standart Tools. ISN doesn't match Car won't start THX and REP will be nice
|
|||
18-12-2016, 02:22 AM,
Post: #6
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
(05-12-2016, 19:54 PM)Sabreace Wrote:Quote:With tool 32 you must enter 18 Which program can align ISN with cas? |
|||
18-12-2016, 10:26 AM,
Post: #7
|
|||
|
|||
Change VIN in ECU with WinKFP possible?
(18-12-2016, 02:22 AM)dazuc Wrote:(05-12-2016, 19:54 PM)Sabreace Wrote:Quote:With tool 32 you must enter 18 Just programming on the table. You Can not change ISN via OBD Wysłane z iPhone za pomocą Tapatalk |
|||
18-12-2016, 13:38 PM,
Post: #8
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Quote:Which program can align ISN with cas? My favourite is BMW Explorer THX and REP will be nice
|
|||
20-12-2016, 02:02 AM,
Post: #9
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Dear getaibose,
I wonder you have resolved your problems yet? But in my knowledge there are some ways to reuse the second hand DME 1st/ making use of tool32 to change vin, and then pass the configuration to DME ( I'm not sure becase of not trying doing this way) but i have found some information on M3 BMW 2st/ utilizing WINKFP to change VIN, and then pass FA from CAS to DME 3st/ Universal programmer will save the day look for the VIN, and blank it. HOWEVER, I have also found some comments mentioning about locking byte on BMW as of MY2008. |
|||
29-01-2017, 11:04 AM,
Post: #10
|
|||
|
|||
RE: Change VIN in ECU with WinKFP possible?
Ok, I forgot to post back here -- I did manage to solve it. I got the ECU, CAS and Key from donor car -- which was a manual.
I used WinKFP to flash automatic car ECU software to the donor car ecu. after that, I copied wrote VO code of the original car to the donor car CAS. Finally after writing new VO code to CAS, I coded the CAS to default using ncsexpert again, now the car started. The only problem is that the VIN number is now of the donor car in the ECU and CAS - and I think changing VIN of the new cas to the original car will cause problem with the Key, as the key has vin of the donor car and might not start if there is vin mismatch with cas? I am not too sure of this, BMW experts here can comment on this further |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
WinKFP can't find ZUSB 6957356 | andre426hemi | 4 | 203 |
25-03-2024, 00:40 AM Last Post: armenh7 |
|
BMW e39 530d 2001 problem after MAF change | boweld11 | 3 | 102 |
24-03-2024, 22:44 PM Last Post: SkeYT |
|
[Question] Change X1 F48 gearbox | jaramillo | 9 | 1,361 |
24-03-2024, 21:27 PM Last Post: masa52 |
|
How to change VIN code in VCM via Esys? | vipsha | 5 | 1,334 |
14-03-2024, 22:20 PM Last Post: tcp443 |
|
FLM change | TomSab | 0 | 74 |
12-03-2024, 19:17 PM Last Post: TomSab |
|
F48 CID change | qbek90 | 0 | 89 |
10-03-2024, 09:13 AM Last Post: qbek90 |
|
Change NBT Evo iDrive 6 Lite Main Menu Car Widget | bradsm87 | 6 | 468 |
07-03-2024, 06:23 AM Last Post: RuleNormaliai |
|
Lane change warning, front left slave not installed | MrM10 | 2 | 107 |
29-02-2024, 12:40 PM Last Post: MrM10 |
|
cas2 change vin | JaVlk | 29 | 934 |
27-02-2024, 18:02 PM Last Post: JaVlk |
|
F30 B48 power class change | dominpl | 1 | 164 |
26-02-2024, 18:05 PM Last Post: ben1978 |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content