Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Ultimate Ediabas/ISTA+ voltage control V3
08-07-2017, 07:22 AM,
Post: #51
RE: Ultimate Ediabas/ISTA+ voltage control V3
V3 version is the same, however until I have time to create a universal solution for IstaOperation.exe, I have to build my fake one for each specific version. Original one changes a bit too, so I may as well wait until it stabilizes a bit. Its new exe which first appeared in 4.05. So I just added a new one for last version.
Quote this message in a reply
[+] 10 users say Thank You to Node for this post
23-07-2017, 07:43 AM,
Post: #52
RE: Ultimate Ediabas/ISTA+ voltage control V3
When I use Enet-cable I see no kl-15 or kl-30? With usb-obd no problems.
Quote this message in a reply
23-07-2017, 15:06 PM, (This post was last modified: 23-07-2017, 15:37 PM by Node.)
Post: #53
RE: Ultimate Ediabas/ISTA+ voltage control V3
Added support for v4.06.31.

(23-07-2017, 07:43 AM)snypertje Wrote:  When I use Enet-cable I see no kl-15 or kl-30? With usb-obd no problems.

Well, it is locked to be active when interface is set to ediabas only. Its easier to support automatic ignition sense over ediabas that way (for interfaces which do support that). You can use enet connection over ediabas as well.
Reputation: +2 - Bimmer540 [+1] , ruben_17non [+1]
Quote this message in a reply
[+] 4 users say Thank You to Node for this post
27-07-2017, 08:50 AM,
Post: #54
RE: Ultimate Ediabas/ISTA+ voltage control V3
I can't find can32.dll in V3 or V2. There is the obd32.dll, but no dll for other cables. Am I missing something here?


1. If you are using STD:OBD rename existing obd32.dll to obd32.ebas.dll. Users of other cable types rename respective dll (for example STD:CAN users rename can32.dll to can32.ebas.dll).
Quote this message in a reply
27-07-2017, 13:02 PM,
Post: #55
RE: Ultimate Ediabas/ISTA+ voltage control V3
Depends on the interface type in ediabas.ini. Most CAN cables still use STD:OBD. But if your cable requires STD:CAN as interface, then you rename existing can32.dll to can32.ebas.dll and rename supplied obd32.dll to be new can32.dll. My wrapper dll is the same for all cable types.
Quote this message in a reply
12-08-2017, 00:37 AM,
Post: #56
RE: Ultimate Ediabas/ISTA+ voltage control V3
Node, just downloaded and installed your v3 kit for 4.05.31. After starting the EdiabasVoltageControl, and then starting ISTA, it locks up on "Please be patient" with the floating bar. Eventually it stops working altogether and I just close the program. Any idea what could be causing the issue?
Quote this message in a reply
12-08-2017, 08:16 AM,
Post: #57
RE: Ultimate Ediabas/ISTA+ voltage control V3
Have you added "AllowFakeISTAOperation" to registry?
Quote this message in a reply
14-08-2017, 03:20 AM,
Post: #58
RE: Ultimate Ediabas/ISTA+ voltage control V3
(12-08-2017, 08:16 AM)Node Wrote:  Have you added "AllowFakeISTAOperation" to registry?

Yep, I did. I can double check through regedit though, where would the changes be?
Quote this message in a reply
14-08-2017, 06:41 AM,
Post: #59
RE: Ultimate Ediabas/ISTA+ voltage control V3
(14-08-2017, 03:20 AM)pgahopeful26 Wrote:  
(12-08-2017, 08:16 AM)Node Wrote:  Have you added "AllowFakeISTAOperation" to registry?

Yep, I did. I can double check through regedit though, where would the changes be?

Where did you put the files?
Quote this message in a reply
14-08-2017, 18:46 PM,
Post: #60
RE: Ultimate Ediabas/ISTA+ voltage control V3
Renamed existing obd32.dll to obd32.ebas.dll (inside Rheingold/Ediabas/Bin)
Put obd32.dll in Rheingold\Ediabas\Bin
Copied NodeISTAVoltageControl.dll to Rheingold\Ediabas\Bin
I'm running 4.05+, so I replaced existing IstaOperation.exe with included one for my version.
Ran the AllowFakeISTAOperation.reg file (x64 for my system)... Prompt came up, I clicked yes to allow, and it confirmed changes were made.

What did I miss?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  ista for use whit vcx se db8000 0 20 1 hour ago
Last Post: db8000
  ista 4.46 Standalone kiranabc 31 2,824 2 hours ago
Last Post: kiranabc
  AOS Ista possible to deactivate second check after scan? RaoulK1998 17 279 6 hours ago
Last Post: RaoulK1998
XZBMW ISTA 4.46.xx problems and possible solution Sedoy 76 7,270 Yesterday, 20:02 PM
Last Post: Node
XZBMW ISTA Standalone Licenserequest up to v4.37.4x Sedoy 8,646 627,336 Yesterday, 16:29 PM
Last Post: Sedoy
XZBMW Update ISTA at once 4.43.40 (ISTA Update Program) charlesjyw 34 6,432 Yesterday, 10:39 AM
Last Post: MINIGP1610
XZBMW BMW ISTA-P Rheingold 69.0.200 (Torrent File) carsoftcare 1 120 26-03-2024, 12:09 PM
Last Post: hlip
  ISTA launcher problem Red_bean_bun 1 155 26-03-2024, 05:11 AM
Last Post: 2013m5
XZBMW Adding a new vehicle/model to "Reingold" ISTA+ dieselweasel 12 662 25-03-2024, 08:11 AM
Last Post: Node
  REQUEST ista 4.45.21 the ISTAGUI.exe file ddsx 5 324 24-03-2024, 14:15 PM
Last Post: Mathijshee

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content