Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

ISTA P 10007 (CIP) Fault during initialization of EDIABAS
18-02-2017, 07:26 AM,
Post: #1
ISTA P 10007 (CIP) Fault during initialization of EDIABAS
Hi, hoping someone can help with this error. I'm getting these errors in ISTA-P:

94201 Technical service initialization failed
-2 Global.Unknown
55054 Global.Unknown
10007 (CIP) - Fault during initialization of EDIABAS

Any help will be greatly appreciated. Thanks!

I'm trying to connect to an F30 (2015, 328) using ENET. EDIABAS runs but the icon turns red and then I get the errors. I enabled logging in EDIABAS:

trace.bip http://pastebin.com/zpGqc1PS
trace.sys http://pastebin.com/71R0HVwN
trace.net http://pastebin.com/aaBtaZDT

Things I've confirmed:
- ISTA-P version: 3.59.4.004
- ISTA-P loader: BMW ISTA-P Loader V6.1F
- The car's IP address is 169.254.88.109 and I can ping it from inside Windows.
- ISTA D works
- Installed patched EDIABAS 7.3
- Disabled firewalls
- No antivirus
Quote this message in a reply
[+] 2 users say Thank You to Ms4246 for this post
18-02-2017, 07:42 AM,
Post: #2
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
I have the same problem. Let's see if someone can help us. I have reinstalled again ISTA-P, I changed it from hard drive D: to C: and I have tried with LOADER 4.9 with the same result.

Enviado desde mi SM-J510FN mediante Tapatalk
Quote this message in a reply
18-02-2017, 10:14 AM,
Post: #3
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
(18-02-2017, 07:42 AM)fitacuevas Wrote:  I have the same problem. Let's see if someone can help us. I have reinstalled again ISTA-P, I changed it from hard drive D: to C: and I have tried with LOADER 4.9 with the same result.

Enviado desde mi SM-J510FN mediante Tapatalk



Same issue here i try my best and everying i know ... but no luck at all ..
Quote this message in a reply
18-02-2017, 13:40 PM,
Post: #4
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
Are you using ENET cable?
ISTA/P ONLY WORK WITH ICOM.
Quote this message in a reply
18-02-2017, 18:58 PM,
Post: #5
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
(18-02-2017, 13:40 PM)2013m5 Wrote:  Are you using ENET cable?
ISTA/P ONLY WORK WITH ICOM.

Yes, using ENET cable.
Do I need an ICOM device or can I use an emulator?
Quote this message in a reply
18-02-2017, 19:39 PM,
Post: #6
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
(18-02-2017, 13:40 PM)2013m5 Wrote:  Are you using ENET cable?
ISTA/P ONLY WORK WITH ICOM.
not only.
K-DCAN cable 50/50
ENET cable support 100%!!!

  • BMW software remote installation via TeamViewer.
Quote this message in a reply
18-02-2017, 22:01 PM,
Post: #7
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
(18-02-2017, 18:58 PM)Ms4246 Wrote:  
(18-02-2017, 13:40 PM)2013m5 Wrote:  Are you using ENET cable?
ISTA/P ONLY WORK WITH ICOM.

Yes, using ENET cable.
Do I need an ICOM device or can I use an emulator?

I've solved it !!

In my case, I use k + dcan, edit obd.ini from the folder c: \ ediabas \ bin and change the com port from 9 to 1.
In network connections, rename "network connection" (loopback adapter) to USB and in properties-> tcp / ipv4 put ip 169.254.0.8 Mask 255.255.0.0.

At some point I must have done some installation of edibas patched and networktool.
Quote this message in a reply
18-02-2017, 23:40 PM, (This post was last modified: 18-02-2017, 23:41 PM by beemerboy88.)
Post: #8
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
Here's the config manuals


Attached Files
v6.1 manuals.zip
File Type: .zip
Downloaded: 416 times
Size: 320.46 KB

Reputation: +2 - ocostel [+1] , weby [+1]
Quote this message in a reply
[+] 12 users say Thank You to beemerboy88 for this post
19-02-2017, 02:02 AM,
Post: #9
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
(18-02-2017, 23:40 PM)beemerboy88 Wrote:  Here's the config manuals

beemerboy88, you are awesome. That fixed it.

For others running into the same issue:
- I'm running ISTAP in a VM
- I changed the name of the Network Adapter to 'eth0' (not sure if this matters but anyways)
- Set the IP address to 169.254.1.1 and gateway to 255.255.0.0
- IP address for the car's connection was still the same 169.254.88.109
- After the changes, I pinged the car's address from inside the VM and confirmed that it was connected. (instructions: launch cmd and type 'ping <ip_address_of_car>'). This should work. If ping is unreachable, something isn't right with the networking.
- Using the launcher, first select ENET, type in the IP address from ZGW search.
- Launch ISTA-P and connect!
Quote this message in a reply
[+] 2 users say Thank You to Ms4246 for this post
07-04-2017, 07:46 AM,
Post: #10
RE: ISTA P 10007 (CIP) Fault during initialization of EDIABAS
I have done this like described in the manual, but still this fault (like #1)?!
Using ENET.
Also coding in ISTA+ is not working, fault in measuring plan occurred, but no further description.
Rest of ISTA+ runs fine.
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  ista 4.46 Standalone kiranabc 28 2,690 Less than 1 minute ago
Last Post: edtech
  AOS Ista possible to deactivate second check after scan? RaoulK1998 17 257 2 hours ago
Last Post: RaoulK1998
XZBMW ISTA 4.46.xx problems and possible solution Sedoy 76 7,238 Yesterday, 20:02 PM
Last Post: Node
XZBMW ISTA Standalone Licenserequest up to v4.37.4x Sedoy 8,646 626,503 Yesterday, 16:29 PM
Last Post: Sedoy
XZBMW Update ISTA at once 4.43.40 (ISTA Update Program) charlesjyw 34 6,403 Yesterday, 10:39 AM
Last Post: MINIGP1610
XZBMW BMW ISTA-P Rheingold 69.0.200 (Torrent File) carsoftcare 1 117 26-03-2024, 12:09 PM
Last Post: hlip
  ISTA launcher problem Red_bean_bun 1 154 26-03-2024, 05:11 AM
Last Post: 2013m5
XZBMW Adding a new vehicle/model to "Reingold" ISTA+ dieselweasel 12 659 25-03-2024, 08:11 AM
Last Post: Node
XZBMW M3 F80 LCI Airbag fault Stefan1251 8 224 25-03-2024, 00:18 AM
Last Post: armenh7
XZBMW Ultimate Ediabas/ISTA+ voltage control V3 Node 322 121,413 24-03-2024, 23:45 PM
Last Post: armenh7

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content