Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Icom a1 stops working! No Led but fan run!
08-03-2017, 11:22 AM,
Post: #11
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
(08-03-2017, 09:26 AM)Hitchhiker Wrote: What must i do with this? first say a thank you then open the file and in writing what is done 1 recorded file on a thumb drive mess icom car and poke stick in icom and pressing three small button resist button and bam says ox if you do not take the file should change his nanflasha or RAMchip |
|||
08-03-2017, 12:28 PM,
Post: #12
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Copy the ICOM_Restore.bin to a clean flash drive, insert it into the icom, press and hold the reset button on the icom, turn on the power, all the LEDs will turn red, then release the button and press it 3 times. All the LEDs start flashing red wait about a minute and restart icom
If the recoil was not successful and the icom work does not observe standard symptoms, then it will be necessary to change the flash very often when the update falls nand flash K9F2G08U0BPCB0 an obvious sign of falling nand flush is a small amount of free space 1 ICOM-BootImage is flooded with ICOM-ApplicationImage is not present, at boot time icom the LED flashes red 2 at boot time icom flashes green LED and it is not loaded 3 on the first seconds of the download icom the LED flashes red but then lights up green and icom is loaded 4 at the very beginning all LEDs Flashes red and goes out 5 icom is loaded but the program constantly changes its status |
|||
08-03-2017, 12:33 PM,
(This post was last modified: 08-03-2017, 13:14 PM by Hitchhiker.)
Post: #13
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Sry ! Thank you! 3 times reset button after connecting to 12v supply?!
Gesendet von meinem SM-G930F mit Tapatalk Ok... i do it ... but the leds dont start flashing red or green... Gesendet von meinem SM-G930F mit Tapatalk |
|||
08-03-2017, 15:07 PM,
Post: #14
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
(08-03-2017, 12:33 PM)Hitchhiker Wrote: Sry ! Thank you! 3 times reset button after connecting to 12v supply?! Copy the ICOM_Restore.bin to a clean flash drive, insert it into the icom, press and hold the reset button on the icom, turn on the power |
|||
08-03-2017, 16:53 PM,
Post: #15
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
No led lights up... only when i connect to 12v all leds for 1 second red.. or half second
Gesendet von meinem SM-G930F mit Tapatalk |
|||
08-03-2017, 17:45 PM,
Post: #16
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
I got a similar problem with an old A1. I replaced the part with the OBD plug from another ICOM just for the fun of it, and the ICOM started working again.
I had no success with restoring the software. Hit Thanks and Reputation button if this post helped you.
|
|||
09-03-2017, 07:56 AM,
Post: #17
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Ok.... same problem.. plugin in short flashing one time red... and dead????thx
Gesendet von meinem SM-G930F mit Tapatalk |
|||
09-03-2017, 08:14 AM,
Post: #18
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Could be a fatigued or broken flex cable. Perhaps the cable is making just a hint of a connection, enough to momentarily flash the lights, but not enough to run. I got my $25 icom with a broken flex cable.
|
|||
09-03-2017, 09:05 AM,
(This post was last modified: 09-03-2017, 09:09 AM by Hitchhiker.)
Post: #19
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Ok but is it identiacal with my symptoms?
Gesendet von meinem SM-G930F mit Tapatalk Where can i get parts for icom? Gesendet von meinem SM-G930F mit Tapatalk |
|||
11-03-2017, 08:49 AM,
Post: #20
|
|||
|
|||
RE: Icom a1 stops working! No Led but fan run!
Some ideas?
Gesendet von meinem SM-G930F mit Tapatalk |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Reset Working Hours MEVD17.2.6 E70 | EngineerX | 17 | 1,242 |
18-04-2024, 17:05 PM Last Post: SkeYT |
|
[MEGA] Any ESYS Editions + PSDZ Full & Lite + ICOM Firmware + MANUALS + TOOLS | hashtagmaster | 105 | 36,028 |
17-04-2024, 18:36 PM Last Post: hashtagmaster |
|
e90 central locking not working | ELMEPRO | 10 | 365 |
15-04-2024, 12:33 PM Last Post: ELMEPRO |
|
ICOM Firmware (NEXT & A2) always current! | Vojno | 206 | 43,285 |
12-04-2024, 23:36 PM Last Post: bennymx |
|
Poor wifi signal from new ICOM's | bmchicago | 3 | 321 |
12-04-2024, 18:55 PM Last Post: Node |
|
Screen Mirroring not working on EVO | painsage | 5 | 298 |
10-04-2024, 15:05 PM Last Post: painsage |
|
N55 Working Hours | Mefiuu92 | 1 | 224 |
03-04-2024, 16:54 PM Last Post: SkeYT |
|
FEM Not working with ENET but works wtih DCAN | armenh7 | 2 | 281 |
01-04-2024, 20:21 PM Last Post: armenh7 |
|
Solved ✔ ICOM NEXT Error | bmwcare | 4 | 2,489 |
01-04-2024, 11:34 AM Last Post: ivanp |
|
CCC flash WINKFP ICOM | BimmerSLO | 9 | 367 |
29-03-2024, 19:17 PM Last Post: Hoborg |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content