Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
10-03-2017, 19:41 PM,
Post: #1
|
|||
|
|||
PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
HI
got this PUG 406 SW hdi auto gear, from 2001 completed mess up by others garages Car some times not start , connection width BSI to ECU fail some times. Owner bring other BSI to adapt, but same problem , The car have bean in the dealer garage to make SW update DTC-- ECU not good configure I I"m thinking put all new dumps , to clone . engine is RHZ wend the car not start , key immo blink in dash and Diag tool can"t not establish communication BSI S110950410 ecu 1 plug 0281010623 Thank"s in advance Brs ART TECH GARAGE
|
|||
10-03-2017, 19:58 PM,
Post: #2
|
|||
|
|||
RE: PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
Do you know the car pass? If you know it that is means you will not need other dumps. Virginise all of them and try to reprogram using PP2000 tool. Also, when you have an immo isue, do you see on the dash numbers or bars?
|
|||
10-03-2017, 22:23 PM,
(This post was last modified: 11-03-2017, 23:09 PM by mexanico1971.)
Post: #3
|
|||
|
|||
RE: PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
(10-03-2017, 19:58 PM)marianro2007 Wrote: Do you know the car pass? If you know it that is means you will not need other dumps. Virginise all of them and try to reprogram using PP2000 tool. Also, when you have an immo isue, do you see on the dash numbers or bars? Hi thank"s for the input! Yes dash is normal But how do I put dump"s in virgin state ?> Guys I need "29f400 and eeprom for this ecu please Brs ART TECH GARAGE
|
|||
13-03-2017, 06:34 AM,
Post: #4
|
|||
|
|||
RE: PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
Hi guys !
eeprom in ecu is st95080 not typical 95p08 I desolder to read it and , now car start but got these dtc"s P1613 Configuration P0603 Internal Control Module Keep Alive Memory (KAM) Error P1517 EDC15C2-Coded anti-start function P0603 Internal Control Module Keep Alive Memory (KAM) Error Wend I try to config PP2000 give error comunication need ecu dump"s please Brs ART TECH GARAGE
|
|||
13-03-2017, 20:39 PM,
Post: #5
|
|||
|
|||
RE: PUG 406 HDI BSI S110950410 dump and ecu 1 plug 0281010623 Files NEED
HI in the rar you will fond tow fill
1/ for the eprom 95080 it is virgin if you have the pin code programe as new ecu if not let him virgin it will work no problem (car start) 2/the 2ed it is for the flash 29F400 it is the closer one i have i hoppe it will solve your problem Peugeot 406_hdi(110cv)_0281 010 627 1037353401 original GOOD LUCK |