Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
NBT EVO Flash : Can't be switched to Programming Mode
30-10-2018, 10:24 AM,
Post: #1
|
|||
|
|||
NBT EVO Flash : Can't be switched to Programming Mode
Guys, trying to fix issue with few EVO units different benches, different computers
When trying to flash with correct FA (Used many times)...I am getting this : It bricks the unit and only way to recover is by serial connection, which I did, unit comes back ok and works fine But trying to flash them always gives me that fault... Been using those FA and benches for a while, never had such issues, especially with 3 units like any idea? Thanks VCM Update: VCM-Update is deactivated. VCM will not be updated. [C197] ExecutionID=2018/10/30-10:16:06.892 [] prepareTALExecution started [] prepareTALExecution finished [] prepareVehicleForFlash started [] prepareVehicleForFlash finished MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET> MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET> MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET> MCDDiagService<id=84900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RDBI_FTP - ReadDataByIdentifier FlashTimingParameter, description=error: timeout, link=HU_NBT2_63_ETHERNET> MCDDiagService<id=238900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_AAM - RoutineControl ActivateApplicationMode, description=error: timeout, link=HU_NBT2_63_ETHERNET> [] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming or coding mode [HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming or coding mode [] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming or coding mode [] finalizeVehicleFlash started MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_FinalizeVehicleFlash, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET> MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_FinalizeVehicleFlash, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET> [] finalizeVehicleFlash finished [] finalizeTALExecution started [] finalizeTALExecution finished TAL execution finished TAL-Execution finished with status: "FinishedWithError". [C207] TAL execution finished. Duration: "2min 4s". [C206] |
|||
30-10-2018, 13:44 PM,
Post: #2
|
|||
|
|||
RE: NBT EVO Flash : Can't be switched to Programming Mode
does your nbt evo then get suck in a blue screen mode after?
blue flashing mode screen? |
|||
30-10-2018, 14:23 PM,
(This post was last modified: 30-10-2018, 14:25 PM by bmwcoder75.)
Post: #3
|
|||
|
|||
RE: NBT EVO Flash : Can't be switched to Programming Mode
(30-10-2018, 13:44 PM)DJ_B4L Wrote: does your nbt evo then get suck in a blue screen mode after? Yes just tested it reboots into flash mode with blue screen Then e-sys outputs what I posted in my original post. Impossible to get out of flash mode with esys. Have to fix by serial connection to get it back to life. |
|||
31-10-2018, 00:18 AM,
Post: #4
|
|||
|
|||
RE: NBT EVO Flash : Can't be switched to Programming Mode
I have one unit with the same problem, I think the v850's data is currupt, you must upload the right image otherwise it will never work in esys.
|
|||
31-10-2018, 07:40 AM,
(This post was last modified: 31-10-2018, 07:42 AM by bmwcoder75.)
Post: #5
|
|||
|
|||
RE: NBT EVO Flash : Can't be switched to Programming Mode
(31-10-2018, 00:18 AM)lming Wrote: I have one unit with the same problem, I think the v850's data is currupt, you must upload the right image otherwise it will never work in esys. Ok thanks and how do you do that please? Using _dev_uds Tool32 Clear_v850 produce same issue, it just times out. I wont clear v850 |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Manual : How to Flash Any NBTevo ID4 to ID5 or ID6 ECE/US/ASIA | FSCmap | 184 | 53,457 |
24-04-2024, 14:49 PM Last Post: Bag3ban1 |
|
Flash CAS 3 for disable ELV | UnFan | 3 | 213 |
19-04-2024, 08:20 AM Last Post: ravager |
|
Add gear display in D-Mode ZF 8HP | TIGHTFIN | 2 | 441 |
18-04-2024, 12:11 PM Last Post: viki300 |
|
F97/98 2wd mode | jaramillo | 8 | 1,259 |
17-04-2024, 13:43 PM Last Post: Nightrider_67 |
|
Add gear display in D-Mode ZF 8HP | TIGHTFIN | 1 | 197 |
13-04-2024, 09:49 AM Last Post: user_530d |
|
Flash MPPK software 20D B47 (Esys) | ruben_17non | 5 | 586 |
10-04-2024, 21:38 PM Last Post: ruben_17non |
|
BMW G8x M3/M4 CSL EGS flash | weby | 22 | 3,657 |
31-03-2024, 19:48 PM Last Post: Erezbmwm |
|
m2 g87 csl flash | Erezbmwm | 0 | 136 |
31-03-2024, 18:46 PM Last Post: Erezbmwm |
|
bmw i4 G26. Field mode. | leqor | 1 | 242 |
31-03-2024, 02:11 AM Last Post: ymj19880806 |
|
CCC flash WINKFP ICOM | BimmerSLO | 9 | 373 |
29-03-2024, 19:17 PM Last Post: Hoborg |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content