Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Mileage correction Dash Peugeot Mageti Marelli with CArPRog
23-09-2017, 17:24 PM,
Post: #1
|
|||
|
|||
Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Hi.
I want to correct the mileage in Magneti Marelli (Peugeot) with CarProg. I try directly with A6 clip and I can read the Eeprom 95020 but most of the numbers are 0 (not all). I try to read kilometers and CarProg say "CheckSum verification did not pass Unknown version. Any ideas for this? Thanks in advantage. |
|||
23-09-2017, 19:47 PM,
Post: #2
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Your china clone probably cant read eeproms or bad clips, bad connections etc.... lots of issues with carprog use search button or google it. you need better programmer for reading eproms
|
|||
24-09-2017, 15:40 PM,
Post: #3
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
I'm looking for a solution in official web page (CODECARLT) and I've seen that if I short 13 and 14 pins while reading I could read the kilometers. Do you think that it maybe could be the solution? Thanks in advantage.
|
|||
24-09-2017, 19:04 PM,
Post: #4
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
(24-09-2017, 15:40 PM)anjo008 Wrote: I'm looking for a solution in official web page (CODECARLT) and I've seen that if I short 13 and 14 pins while reading I could read the kilometers. Do you think that it maybe could be the solution? Thanks in advantage. I tried with short pin 13 and 14 but eeprom change. All FF. |
|||
24-09-2017, 22:22 PM,
Post: #5
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Try to check read verify check box
check A6 connexions all have this issue some eeprom need to be removed from dash they have write protection |
|||
25-09-2017, 11:01 AM,
Post: #6
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
You cant read the eprom incircuit try to desolder and read again will works fine
|
|||
25-09-2017, 12:08 PM,
Post: #7
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Ok. I will try.
|
|||
26-09-2017, 09:35 AM,
(This post was last modified: 26-09-2017, 09:38 AM by volavka.)
Post: #8
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Hi easier by Smok
|
|||
26-09-2017, 09:39 AM,
Post: #9
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
|
|||
27-09-2017, 21:51 PM,
(This post was last modified: 27-09-2017, 21:53 PM by anjo008.)
Post: #10
|
|||
|
|||
RE: Mileage correction Dash Peugeot Mageti Marelli with CArPRog
Hi all.
I tried. Now change completely the eeprom information. desolder o not the information is very diferent. https://www.dropbox.com/s/g9ihjwzgq4x972...a.JPG?dl=0 Pd: I tried with A4 and A5 CarProg cable. |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
GOLF V 2005 Visteon need mileage correction | Mshumacher | 6 | 60 |
6 hours ago Last Post: sivyx |
|
Beverly 350,93c66 mileage correction, problem | marko.p | 0 | 9 |
9 hours ago Last Post: marko.p |
|
Nissan Murano 2012 mileage correction | Mariushas | 3 | 27 |
03-05-2024, 08:33 AM Last Post: Mariushas |
|
VW Crafter 7C0920731A mileage corection | C(A)R | 6 | 120 |
02-05-2024, 15:55 PM Last Post: iProg-carradio |
|
bmw e60 lcm ahl correction | sepica | 2 | 49 |
30-04-2024, 09:45 AM Last Post: sepica |
|
Yamaha FJR mileage modification | bm92 | 14 | 171 |
30-04-2024, 09:01 AM Last Post: bm92 |
|
2021 VW ID 4 PRO Cluster 10A920320C mileage correction possible ? | NickMayer | 5 | 118 |
28-04-2024, 21:12 PM Last Post: NickMayer |
|
Fiat Talento Dash km correction higher | Cryjack | 4 | 79 |
28-04-2024, 11:59 AM Last Post: iProg-carradio |
|
Nissan NV200 dash | pawel7924 | 4 | 1,407 |
27-04-2024, 14:41 PM Last Post: Ecu_Blast |
|
vito cluster mileage | spoool | 3 | 142 |
24-04-2024, 23:46 PM Last Post: spoool |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content