Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
19-06-2014, 21:12 PM,
Post: #11
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
It's really not clear what is the reason for ERROR 0... it is possible to install it on a laptop? A special network card is needed?
Quote this message in a reply
20-06-2014, 15:04 PM,
Post: #12
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
(19-06-2014, 21:12 PM)garage_neo Wrote:  It's really not clear what is the reason for ERROR 0... it is possible to install it on a laptop? A special network card is needed?

No special network card needed, only you must know some steps...
1) You use DiagBox Cleaner , then clean files from previous failed installations of DiagBox
2) Run CCleaner to clean registry
3) Go to: start windows/run then type "regedit" and check if you see some registry files named "Diagbox" or "actia" in folders Hkey_local Machine and Hkey Current Users, then delete manualy
4) Check drivers if right installed of your wi-fi card on your PC-Laptop
5) Check driver if right installed of your LAN card
6) Turn ON wi-fi, turn ON LAN card, Connect to the ineternet ALL time during installation DiagBox
7) Install Java 6.xx or Java 7.xx (if you dont have installed)
8) Install Microsoft Visual C++2010 or C++2012 (if you dont have installed)
9) Install Microsoft .NET Framework 3.5 SP1 (if you dont have installed)
10) Start install Diagbox...
This is conditions/requirements for healthy windows system, installation always is perfect ( I installed many times DiagBox all versions)
IF stil have ERROR 0, then install fresh windows, and always turn ON wi-fi card and LAN card + all time connected to internet during installation..
yes

Quality tool as the beautiful woman...
Quote this message in a reply
[+] 14 users say Thank You to obdstart for this post
25-07-2014, 10:46 AM,
Post: #13
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
(14-06-2014, 19:48 PM)sbrenda Wrote:  I running on vm. enjoy
The problem is in the vm config.
Work only if hdd is set to "ide", if "scsi" gave error 0
Good luck! yes

THANK YOU!!!
Only need add a new hard disk IDE, (select the same file of SCSI used) and delete SCSI hard disk in configuration.
Quote this message in a reply
16-08-2014, 02:17 AM,
Post: #14
PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
I had problem like tomey3000 to...please help me..tqvm
Quote this message in a reply
13-07-2015, 14:25 PM,
Post: #15
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
(13-03-2014, 08:15 AM)Geri Wrote:  
(12-03-2014, 10:47 AM)lurchy666 Wrote:  When I got activation error 0 it was because my languge settings in windows was set to uk not English us

Error = 0 > MAC-adress network card not found. The network card must be activated to identify the computer.

This is 100% true, my problem was "Disabled LAN Adapter" smile
There was no "ERROR 0" anymore... smile
Quote this message in a reply
04-08-2015, 08:51 AM,
Post: #16
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
Hi guys hope someone can help I have pp2000 installed first time tried to connect it to the car to automatically get the cars information it finds the vin number but when it goes to the next step search for the cars data it fails and says automatic detection of the vehicle interrupted and stops so when I manually put in the vin number it go to the diagbox/pp2000 screen I press on either of them it says turn on the key it the shows the vin number the says ecu not replied press the tick the next screen says it is not possible to run pp2000for the following reason
pp interface is not connected to the pc
pp interface is being used by another app
any ideas please I have installed twice first time with wifi turned on second time it was turned off except when validation of the product also should it take over 30mins just to close the app down I am a bit of a novice at pc stuff any help would be great roger
Quote this message in a reply
20-10-2015, 00:55 AM,
Post: #17
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
I have the same problem with my Peugeot 307. Some people say that China interface with serie B firmware doesn't work in diagbox V7.xx
Quote this message in a reply
20-10-2015, 06:14 AM,
Post: #18
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
If you have an "oldish" Evolution XS (Lexia) device with the "B" Revision, then it cannot operate with DiagBox software version higher than 5.29... PSA has blocked it...

What you need is to flash the device to the "C" Revision.. If you search for Lexia_flash.rar, you will find the flashing kit.

Or, there may be another easier idea (just came to me), I will test it first and if it works well, I will write about it..
Quote this message in a reply
20-10-2015, 22:25 PM,
Post: #19
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
Thanks for the informativo Simples.
So I think is better try using the old diagbox version. But couldn't find it yet tears
Quote this message in a reply
21-10-2015, 03:17 AM,
Post: #20
RE: PSA DiagBox 7.01 - failure of the activation (error 0) - I am going to be mad
Attached are links for DiagBox 5.01 to 5.43 and DiagBox 6.01 to 6.43..

Download and install DiagBox 5.xx up to 5.29 only For revision "B".. You can try anything if you wish..

I also think you need to flash the Lexia device with firmware 4.2.4 or less using "psa interface checker", you will probably find various versions of the firmware under "C:\APP\OUTILREP\EXE\COM\DATA"

By the way, I read somewhere that if you downgrade the Lexia firmware to 4.2.2, it will work with your current DiagBox 6.xx and 7.xx... I cannot confirm, my device is revision "C".


Attached Files
Diagbox 6.43.txt
File Type: .txt
Downloaded: 62 times
Size: 6.71 KB

Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  PSA Diagbox VCI Interfaces alexturbo 18 6,461 27-12-2023, 21:45 PM
Last Post: apol
PPeugeot DIAGBOX 2021 9.85 FULL INSTALATION akli 6 2,538 26-12-2023, 20:21 PM
Last Post: Le-Mans
PCitroen DIAGBOX online walczaklu 10 8,546 03-12-2023, 12:57 PM
Last Post: mattydr67
  DiagBox 7+Updates+Firmware+Drivers+Tools (Magnet) Simple 33 35,309 22-11-2023, 06:16 AM
Last Post: Jeppo
PPeugeot Diagbox 9.129 activation request dadoa4 4 2,351 09-11-2023, 09:59 AM
Last Post: bovhec
  diagbox 9.150 stasi 5 2,050 16-09-2023, 19:41 PM
Last Post: stasi
  DiagBox Language Change Simple 16 17,334 14-09-2023, 10:01 AM
Last Post: żarówka
  DIAGBOX help needed installing mars2moon 4 998 23-07-2023, 18:45 PM
Last Post: J415UNNY
PPeugeot Diagbox 9.91 VmWare gabi2008 6 4,179 23-07-2023, 18:42 PM
Last Post: J415UNNY
  diagbox latest ? Chad69 1 825 09-06-2023, 22:28 PM
Last Post: simo2k

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content