Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Flashed G11 - Kafas broken
15-10-2017, 07:38 AM,
Post: #1
Flashed G11 - Kafas broken
Hi, I flashed a G11 from integration 58 to 61, all went well except the Kafas, which failed to flash.
ISTA tried 3 times, I then tried E-SYS, tried ISTA again, disabled parallel programming in E-SYS, same thing.
I tried to flash with E-SYS again with 59 data, same issue.

Any idea how to recover this?

Here is the error in E-SYS

FlashTimingParameter, description=error: timeout, link=Physical request to ECU with address 0x5d>
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=Physical request to ECU with address 0x5d>
[] Activate programming mode was not successful for: ECUId:KAFAS4_0x5D
[] ECUId:KAFAS4_0x5D not accessible cause could not be switched to parallel programming or coding mode
[KAFAS4 - 5D] ECUId:KAFAS4_0x5D not accessible cause could not be switched to parallel programming or coding mode
[] finalizeVehicleFlash started
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_FinalizeVehicleFlash, service=DSC - DiagnosticSessionControl, description=error: timeout, link=Physical request to ECU with address 0x25>
Quote this message in a reply
15-10-2017, 09:36 AM,
Post: #2
RE: Flashed G11 - Kafas broken
Do you use an icom?

MGU virgin and patching in Europa.
Secure coding 2.0
Feature installer codes
Quote this message in a reply
15-10-2017, 09:49 AM,
Post: #3
RE: Flashed G11 - Kafas broken
(15-10-2017, 09:36 AM)Fx82 Wrote:  Do you use an icom?

Used ICOM with ISTA and ENET and ICOM with E-SYS same thing
Quote this message in a reply
15-10-2017, 19:51 PM,
Post: #4
RE: Flashed G11 - Kafas broken
Did you use a dhcp mode?

MGU virgin and patching in Europa.
Secure coding 2.0
Feature installer codes
Quote this message in a reply
15-10-2017, 23:06 PM,
Post: #5
RE: Flashed G11 - Kafas broken
(15-10-2017, 19:51 PM)Fx82 Wrote:  Did you use a dhcp mode?

Never ever used dhcp in my bmw programming life.
Quote this message in a reply
16-10-2017, 05:35 AM,
Post: #6
RE: Flashed G11 - Kafas broken
Run the connection through a router. ICOM or ENET cable to router, router to computer.
Quote this message in a reply
16-10-2017, 06:46 AM,
Post: #7
RE: Flashed G11 - Kafas broken
Hello!

Or the simple method - flash it again with an enet cable, not with the ICOM.

CU Oliver
Quote this message in a reply
16-10-2017, 08:09 AM,
Post: #8
RE: Flashed G11 - Kafas broken
During vehicle management, one of the following Ethernet-capable control units should be programmed:HU-H, RSE, ATM, KOMBI, ACC, ICAM, KAFAS
At the start of the session, a note appears indicating that the IP address is invalid. The Ethernet programming can fail if the following steps are not followed:

Model series affected:
All F, G, I Series

Measure/workaround:
1. Finish ISTA(P) session
2. Carry out a battery reset
3. Restart the session
4. If the fault message continues to appear: Check that the Ethernet wiring in the vehicle corresponds to the wiring diagram in ISTA
5. If the fault message continues to appear: Contact Technical Support

Fault corrected by:
Currently still open

Affected application:
ISTA/P
ISTA 4
Quote this message in a reply
[+] 4 users say Thank You to Jumper for this post
16-10-2017, 13:48 PM, (This post was last modified: 16-10-2017, 13:51 PM by bmwcoder75.)
Post: #9
RE: Flashed G11 - Kafas broken
(16-10-2017, 06:46 AM)milkyway Wrote:  Hello!

Or the simple method - flash it again with an enet cable, not with the ICOM.

CU Oliver

I did with E-SYS, same issue

(16-10-2017, 08:09 AM)myfirst1er Wrote:  During vehicle management, one of the following Ethernet-capable control units should be programmed:HU-H, RSE, ATM, KOMBI, ACC, ICAM, KAFAS
At the start of the session, a note appears indicating that the IP address is invalid. The Ethernet programming can fail if the following steps are not followed:

Model series affected:
All F, G, I Series

Measure/workaround:
1. Finish ISTA(P) session
2. Carry out a battery reset
3. Restart the session
4. If the fault message continues to appear: Check that the Ethernet wiring in the vehicle corresponds to the wiring diagram in ISTA
5. If the fault message continues to appear: Contact Technical Support

Fault corrected by:
Currently still open

Affected application:
ISTA/P
ISTA 4

I did not have any error message
Never seen that one
Quote this message in a reply
16-10-2017, 15:45 PM,
Post: #10
RE: Flashed G11 - Kafas broken
(15-10-2017, 23:06 PM)bmwcoder75 Wrote:  
(15-10-2017, 19:51 PM)Fx82 Wrote:  Did you use a dhcp mode?

Never ever used dhcp in my bmw programming life.

Great! Now it is time for a change....yes you can biggrin

MGU virgin and patching in Europa.
Secure coding 2.0
Feature installer codes
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  NBT ID3 screen on ID4 flashed to ID6 Driss2 2 139 27-03-2024, 11:46 AM
Last Post: RuleNormaliai
XZBMW Request KAFAS FSC repair pack miru75 74 8,332 23-03-2024, 17:50 PM
Last Post: radeeek17
  Broken CIC stuck in bootloop painsage 5 248 28-02-2024, 17:13 PM
Last Post: Chillmeister
  KAFAS models knowledge roundup anstr 8 432 06-02-2024, 18:54 PM
Last Post: jb2005
XZBMW Speed limit information on G cars with one kafas pcp1234 1 220 27-01-2024, 18:35 PM
Last Post: dasi
  FSC for Kafas 4 11F OEM Or Patch cupra80 2 425 21-11-2023, 11:02 AM
Last Post: Wojti77
  F44 EGS broken qbek90 3 348 05-11-2023, 19:34 PM
Last Post: DEJMIEN
  Solved ✔ Kafas 2 flash Jalami 4 345 05-11-2023, 18:12 PM
Last Post: Jalami
  N63 was tuned. Flashed with stock but still writes tuned. Why? bmwlover 3 325 01-11-2023, 23:35 PM
Last Post: Yah
  Kafas 4 virgin ? iliannavy 5 1,039 24-10-2023, 10:10 AM
Last Post: BimmerSLO

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content