[Patrick11021979]

Odd try battery reset all 3 of them , and or zgm special measure aka manually select software update

ZGM special measure?

Check Puma:63282800-03

If flexray is not recognized, use ista/p to program car and except measureplan...

Greets Patrick

Can you send Me exact description of this document? I should update whole car?


Sent from my iPhone using Tapatalk

Yes, update complete car with ista/p, there will be a special measurement plan.. Accept it, and do what Ista/p says.....
This should fix your problem, if you do no have wiringproblems from accident...

Greets Patrick

[kmodel99]

Odd try battery reset all 3 of them , and or zgm special measure aka manually select software update

ZGM special measure?

Check Puma:63282800-03

If flexray is not recognized, use ista/p to program car and except measureplan...

Greets Patrick

Can you send Me exact description of this document? I should update whole car?


Sent from my iPhone using Tapatalk

Yes, update complete car with ista/p, there will be a special measurement plan.. Accept it, and do what Ista/p says.....
This should fix your problem, if you do no have wiringproblems from accident...

Greets Patrick

I will try at Wednesday or later. I need to update each module (update from 16-03 to 17-x).

Today I inspected each cable, VTG and EPS have power (+12V and GND), and flexray (checked for continuity and short circuit to GND and +12V).
DDE have power from rear fuse box, flexray and PTCAN also is ok. Only think I didn’t inspect is a integrated supply module (near DDE), I will check this today or tomorrow.


Sent from my iPhone using Tapatalk

[Patrick11021979]

Odd try battery reset all 3 of them , and or zgm special measure aka manually select software update

ZGM special measure?

Check Puma:63282800-03

If flexray is not recognized, use ista/p to program car and except measureplan...

Greets Patrick

Can you send Me exact description of this document? I should update whole car?


Sent from my iPhone using Tapatalk

Yes, update complete car with ista/p, there will be a special measurement plan.. Accept it, and do what Ista/p says.....
This should fix your problem, if you do no have wiringproblems from accident...

Greets Patrick

I will try at Wednesday or later. I need to update each module (update from 16-03 to 17-x).

Today I inspected each cable, VTG and EPS have power (+12V and GND), and flexray (checked for continuity and short circuit to GND and +12V).
DDE have power from rear fuse box, flexray and PTCAN also is ok. Only think I didn’t inspect is a integrated supply module (near DDE), I will check this today or tomorrow.


Sent from my iPhone using Tapatalk

Ista/p automatically update the modules, you do not have to select anything, or update seperately. It's common problem that you don't see flexray units in three of ista/d...

greets

[kmodel99]

Ista/p automatically update the modules, you do not have to select anything, or update seperately. It's common problem that you don't see flexray units in three of ista/d...

greets

I know. ISTA/P also doesn't see this ECUs. In this week I will bring car from mechanic to my home and I will try to update whole car. I tested Integrated Supply Module and it's ok.

[kmodel99]

Thanks to all! I updated whole car with ista, then do flexray initialization and it works.

I need to manually disable some actions in ista because it wanted to replace DDE and EPS to new one.

But now I have problem because I can’t update KAFAS, ICAM, SWW, and every media unit (HU-H, AMP, VM, RSE). Ista shows “NotExecutable”.

I think SWW won’t update because I didn’t install lane change assist front left and right, icam because I didn’t install front camera.

But kafas is ok, it is original from this car and now it want new FSC codes for traffic sign recognition, pedestrian protection, lane departure warning. Does anybody have any idea?

EDIT; it wasn’t a problem with wiring, only software problem.

[Mwahab]

Glad you found the solution. (Y)

I was having a similar problem, but it wasn't the DDE, it was the ICM.
I was not able to move the car or change the gear or anything.

Problem fixed by initialising the FlexRay manually via tool32.

ICM appeared as well with EPS and some other modules that it couldn't be read in ECU tree.