[galaxia]

Hello everyone.
I have installed Diagbox V7.xx on my PC, installation is all Ok, but the problem is to open and close the Diagbox application, it is very, very slow !!!!!

When I connect "diagbox" it takes a long time to load the application, the home screen is 15 minutes or more !!!!

To close the "diagbox" application, the same problem, it says "the application is being closed" plus it takes too long, 15 minutes or more to close "diagbox" application. !!!!!!

I have windows xp sp3 bit with VMware machine 12
I am suffering a lot, I am tired with the installation of this "diagbox" I have already done many installations without success, it does not work beyond V.7.57,
I am discouraged.

How do I solve this problem?

[xander20005]

"I have windows xp sp3 bit with VMware machine 12" this is the problem

install on laptop, without vmware. to work in wmvare you need a laptop with good proc/ram etc
or buy another laptop

[galaxia]

"I have windows xp sp3 bit with VMware machine 12" this is the problem

install on laptop, without vmware. to work in wmvare you need a laptop with good proc/ram etc
or buy another laptop

Ok, buy another laptop.
Now about V7.57 version, how do I make V7.57 + update ?

message is "access data problem" and close aplication !!!
For me works only up V7.57
some idea ?

[Simple]

Ensure that you have "Virtualization" is enabled in the BIOS and go through the posts to check if all configurations and needed software are performed; if no joy:

Use VistualBox, it is FREE and MUCH faster, review "DiagBox 8.01 Installation" thread under "Preparation for Installing DiagBox 8.01 on VirtualBox", it is the same for all DiagBox versions.
Download and install VirtualBox executable, then while VirtualBox is closed, download and install VirtualBox_Extension_Pack, then start installing Windows XP accepting standard settings; if you wish, then ensure the following parameters in "Settings":

1- Settings -> System:
a- Allocate 1.5 GB RAM or more,
b- Make sure that "Enable I/O APIC" is NOT checked.
c- Allocate 1 CPU

2- Settings -> Display:
a- Allocate 128 mb Video Memory.

3- Settings -> USB:
a- Enable USB controller "Checked" -> USB 2.0 (Checked)
b- Click on USB icon with round green dot (this will make the guest Windows recognise and connect any USB device)

Notice:
1- A connected USB device will ONLY be available to either the Host or the Guest operating system, but NOT to both.

2- If you click the Add USB icon with green plus, it will list available/connected USB devices (Camera, Card Reader, USB memory, VCI etc..). The device you choose here will ONLY be recognised by the guest Windows.

3- If you insert a USB device (like a memory stick) that is read by the guest Windows, it will not be seen by the host Windows until you disable (uncheck) USB or shutdown guest Windows.

When Windows XP is installed and started, click on Menu -> Devices -> Insert Guest Additions CD image. If it does not start by itself, navigate to "D:\" and start it and accept the challenges (Continue Anyway).

Now start DiagBox installation process, you should notice the speed difference.

Good luck, Simple.

[xander20005]

Ok. now really. Why do you need newer update? I use 7.66 and its enaugh for me? Anyway if u not have access to server its useless.

[galaxia]

Ok. now really. Why do you need newer update? I use 7.66 and its enaugh for me? Anyway if u not have access to server its useless.

My car is Peugeot Boxer 2013, Diagbox V7.57 not works with it, I need version above.

[Simple]

Did you try this post ??

http://cartechnology.co.uk/showthread.php?tid=24161

[xander20005]

Boxer 3 need additional adapter to work. from 7.0.2 diagbox knows boxer 3

---

here is the adapter

[galaxia]

Boxer 3 need additional adapter to work. from 7.0.2 diagbox knows boxer 3

---

here is the adapter

Ok, but my car is not CAN-bus , it is K-line only !!!!
Engine ECU is Magneti Marelli MJ8DF CF3 euro-iv

no can-bus

[xander20005]

Give me the chassis number