[netgear2]

Thanks again beemerboy88, You are a GENIE!!! flashed the ICOM with your suggested latest firmware and voila!!!
Now stuck with this dreaded KMM 1207 error when ISTA/P attempts to calculate the measure plan.
Not much information after searching forums etc. Any ideas please??
I looked through the link you posted to help someone else regarding this error but no solution there, just questions.
No idea why!! errmm few retrofits in car here and there but nothing unusual except retrofitted ACC module died on me few weeks back after unsuccessfull Winkfp flash. Had to buy the ICOM to revive that.

[sharkbite]

Hi, is this for parts also? Like EPC by vin?

[slaw1971]

Hello
I have a problem with ISTA P in F- series
cars before I-LEVEL, 2011 - works well
cars after the I-LEVEL, 2011 - It is not possible to create an action plan, or all the computers after the creation an action plan is for exchange - according to a program
any solutions?

Best Regards

[ap90500]

Hello
I have a problem with ISTA P in F- series
cars before I-LEVEL, 2011 - works well
cars after the I-LEVEL, 2011 - It is not possible to create an action plan, or all the computers after the creation an action plan is for exchange - according to a program
any solutions?

Best Regards

I have the same problem, this version is faulty I think.

[netgear2]

Hello
I have a problem with ISTA P in F- series
cars before I-LEVEL, 2011 - works well
cars after the I-LEVEL, 2011 - It is not possible to create an action plan, or all the computers after the creation an action plan is for exchange - according to a program
any solutions?

Best Regards

I have the same problem, this version is faulty I think.

Hi Guys,

I can confirm the version is not faulty. Ran measure plan on my friends 2011 X5 which is completely stock (no modifications or retrofits) and has integration level july 2014 (vehicle went in for some warranty workl ast week) , no problems at all, ISTA/P ran like a charm. Its something to do with retrofits etc because my car has CIC retrofit and tunes DDE and ISTA/P does not want to know my car..

[ap90500]

My car does not have complicate retrofits, also ista/p 51.3 works with it. This version want's to replace every module and gives error when trying to calculate final measures plan. 2011 x5 is e-series, these problems arise when using this version on f-series.

[delirio]

Hi,

I was trying to connect by ENET to my car and encountered several problems:
running /D, it was showing the ICOM, the VIN as well as the voltage of K15/K30, but I was not able to read any ECUs.

running /P, it only showed the ICOM, but with red status in last column (not usable). I was starting it several times, but with no success (in contrast to /D, it showed not even the K15/K30 voltage).

Can somebody give me a hint? Thx!

[beemerboy88]

Hi,

I was trying to connect by ENET to my car and encountered several problems:
running /D, it was showing the ICOM, the VIN as well as the voltage of K15/K30, but I was not able to read any ECUs.

running /P, it only showed the ICOM, but with red status in last column (not usable). I was starting it several times, but with no success (in contrast to /D, it showed not even the K15/K30 voltage).

Can somebody give me a hint? Thx!

could be a network error. Recheck that you have set up the emulator network settings correctly.

also make sure you start the software in this order:

1. boot ista to the main screen and wait until red writing disappears.
2. start the emulator and set it up for ENET (confirm connection to car etc.).
3. Now start ista/d or ista/p session using relevant icon on the main screen.

[netgear2]

Hi beemerboy88, can you please help us with the KMM 1207 error?

[beemerboy88]

Hi beemerboy88, can you please help us with the KMM 1207 error?

ista/p likely is failing because there something wrong with the VO of the car. its trying to find a module that isn't there anymore. try correcting vo using ncs expert. then retry ista/p.