Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
SDconnect UART error
23-08-2014, 07:13 AM,
Post: #1
|
|||
|
|||
SDconnect UART error
Selftest gives UART test = 8 (tested with 07.2014 and some 2012 software in different computer).
However, everything seems to work perfectly (atleast at 2x CDI w211 I tried), so should I be concerned about the error? MUX is notorious 1010XX china clone. Here´s the ceasar: Code: Selfdiagnostic What chip is this in the board and is it possible/easy to replace? |
|||
23-08-2014, 19:41 PM,
Post: #2
|
|||
|
|||
RE: SDconnect UART error
Do you have fully charged and calibrated batteries in?
I would say youre OK. |
|||
24-08-2014, 06:21 AM,
Post: #3
|
|||
|
|||
RE: SDconnect UART error
(23-08-2014, 19:41 PM)JarsaR Wrote: Do you have fully charged and calibrated batteries in? No, it is not OK, look: UART test: 8, that is serious error and can not be ignored, that SDC will malfunction in connection with real vehicle. and for: PMPIC test: 8, you are right, it is just sign that ceaser test was run without or with weak batteries, that error can be ignored. Regards! |
|||
24-08-2014, 06:31 AM,
Post: #4
|
|||
|
|||
RE: SDconnect UART error
Hey,
I did not notice the other error. |
|||
24-08-2014, 07:14 AM,
Post: #5
|
|||
|
|||
RE: SDconnect UART error
Thanks for your replys.
Strangely the MUX works perfectly in two diesel w211 I have, no problems at all Does anybody know what chip this UART is on the board and is it hard to find new one and replace it by my self + ask for partial refund? Or should I just send the MUX back to seller and take my money back? (23-08-2014, 19:41 PM)JarsaR Wrote: Do you have fully charged and calibrated batteries in?How can I calibrate the batteries? I haven´t got the batteries to work properly in any of the china clones, when I´ve installed them? |
|||
24-08-2014, 08:55 AM,
Post: #6
|
|||
|
|||
RE: SDconnect UART error
(24-08-2014, 07:14 AM)sonikki Wrote: Thanks for your replys. Hey, i usually charge the batteries fully, before putting them into unit. After that, just leave the unit in car charging, batteries will be calibrated in few hours. You can see from the display, when the batteries are calibrated, the line enclosing the battery image, will turn solid. |
|||
24-08-2014, 13:02 PM,
Post: #7
|
|||
|
|||
RE: SDconnect UART error
Does it matter what kind of batteries I use? Usually when I´ve tried to install batteries, they charge for a while and MUX starts to display "batteries cannot be charged" at the screen?
|
|||
24-08-2014, 14:25 PM,
Post: #8
|
|||
|
|||
RE: SDconnect UART error
(24-08-2014, 13:02 PM)sonikki Wrote: Does it matter what kind of batteries I use? Usually when I´ve tried to install batteries, they charge for a while and MUX starts to display "batteries cannot be charged" at the screen? Yes, it does, you should use NiCD Batteries 1.2 V, but with capacity of max. 700mAh. Please take a note that chinese clones often have low quality voltage regulator circuit elements and cannot drive higher capacity of NiCD batteries like 2000 and more mAh. Regards! |
|||
18-01-2017, 22:47 PM,
Post: #9
|
|||
|
|||
RE: SDconnect UART error
I've read that a UART error may be caused by a defective relay contact.
If I can replace my LAN board on.my old mux, I'll try to see why my old one had a UART error.... BR Learning is good, SHARING is BETTER
If my post helps you, don't be shy, say thanks & rep ! |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Xdos 2024.03 version _ novapdf error[Solved] | smlee747 | 0 | 132 |
09-04-2024, 08:33 AM Last Post: smlee747 |
|
Xentry error | nixte | 4 | 146 |
08-04-2024, 11:52 AM Last Post: nixte |
|
SDconnect c4 not working with DAS | passador83 | 3 | 192 |
28-03-2024, 15:34 PM Last Post: gcs190 |
|
addons error | maxs30 | 0 | 82 |
11-02-2024, 14:17 PM Last Post: maxs30 |
|
sdconnect c4 doip vs. xdos version | tintoverano | 3 | 354 |
01-12-2023, 15:42 PM Last Post: gcs190 |
|
xentry start error | Ahson wajid | 6 | 399 |
15-11-2023, 18:29 PM Last Post: Automotive 1 |
|
Could not extract script from EXE xentry installation error | Automotive 1 | 0 | 141 |
08-11-2023, 06:29 AM Last Post: Automotive 1 |
|
Check the ETC device error - removing DSRC unit NTG 5.5 | andsol | 0 | 116 |
29-10-2023, 08:02 AM Last Post: andsol |
|
300CE 24 + Xentry + SDconnect | Liteace | 6 | 521 |
17-10-2023, 20:39 PM Last Post: Liteace |
|
Xentry doesnt start error | chillaaa | 6 | 583 |
05-10-2023, 16:15 PM Last Post: gcs190 |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content