Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Does Nissan Consult III work with Renault CAN CLIP software?
29-05-2015, 21:03 PM,
Post: #11
RE: Does Nissan Consult III work with Renault CAN CLIP software?
(12-09-2014, 16:50 PM)Khaleal Wrote:  Hi,

I was wondering if a Nissan Consult III hardware works with Renault CAN CLIP (v139 for example)?
This is the Consult III I'm talking about (Chinese clone)
[Image: Nissan_consult_III_diagnostic_set.jpg]

[Image: Nissan%20Consult%203%20OBD2%20Profession...ool_03.jpg]

And if yes.. Will it support reprogramming, etc..? And is it recommended over SONDE as it has the newer Alliance PCB..
i think you can not use the can clip software for nissan consult3
it give a special software for nissan concult 3
Quote this message in a reply
18-09-2015, 19:32 PM,
Post: #12
RE: Does Nissan Consult III work with Renault CAN CLIP software?
Does anyone sell original HW Consult3 (not a clone)? Or you can advise where to buy really good clone? In the photo,, A,, is good clone. In the photo,, B,, is already low quality version. Does anyone know where to buy exactly the same hardware as the picture,, A,,?
However, if someone sells original HW Consult3, so it interests me the most.
Thanks for any help and sorry for bad English.


Attached Files Thumbnail(s)
       
Quote this message in a reply
19-09-2015, 07:00 AM,
Post: #13
RE: Does Nissan Consult III work with Renault CAN CLIP software?
You can buy also a chinese clone ( alliance consult3, CAN-clip sonde ) there are not so bad people say... Latest years chinese make better and better tools, anyhow 90% electronic goods are chinese made ( look the back of your TV set and you will see for sure " Made in China " )
And yes, Alliance 3 works with CAN -clip software, even the Reno-Nissan representatives work with CAN-Clip sonde and Alliance 3 with the same laptop on CAN-Clip software.
And yes, they also use chinese clones ( Alliance and CAN-Clip sonde ), no one else manufacturing these hardware tools but the chinese.nod
Quote this message in a reply
[+] 8 users say Thank You to alfabit for this post
02-06-2016, 04:00 AM,
Post: #14
UNissan  RE: Does Nissan Consult III work with Renault CAN CLIP software?
(12-09-2014, 16:50 PM)Khaleal Wrote:  Hi,

I was wondering if a Nissan Consult III hardware works with Renault CAN CLIP (v139 for example)?
This is the Consult III I'm talking about (Chinese clone)
[Image: Nissan_consult_III_diagnostic_set.jpg]

[Image: Nissan%20Consult%203%20OBD2%20Profession...ool_03.jpg]

And if yes.. Will it support reprogramming, etc..? And is it recommended over SONDE as it has the newer Alliance PCB..

Consult 3 and CAN CLIP Use the same hardware - here
Renault can clip hardware is good for nissan consult software,it is able to diagnose nissan cars with renaul can clip hardware!!! (sp19-b and sp38-b)
very well and cheaper
Quote this message in a reply
[+] 4 users say Thank You to obdtool for this post
11-07-2016, 04:32 AM,
Post: #15
RE: Does Nissan Consult III work with Renault CAN CLIP software?
1: the clone of nissan consult 3 VI from China is not the 100% copy, It's only have a C3 cover, so if you want use it you must make a software patch to instant the original driver of C3
2: In China the dealer of Renault is use the NISSAN C3 for an offical origianl diagnostic tool.
So if you have an original c3 you can use it for Renault CANCLIP ,But if you have a clone one, you should make a patch at first,then you must test it by youself.
Quote this message in a reply
[+] 2 users say Thank You to DOWNLOADIX for this post
15-12-2016, 00:10 AM,
Post: #16
RE: Does Nissan Consult III work with Renault CAN CLIP software?
(18-09-2015, 19:32 PM)pb1234 Wrote:  Does anyone sell original HW Consult3 (not a clone)? Or you can advise where to buy really good clone? In the photo,, A,, is good clone. In the photo,, B,, is already low quality version. Does anyone know where to buy exactly the same hardware as the picture,, A,,?
However, if someone sells original HW Consult3, so it interests me the most.
Thanks for any help and sorry for bad English.
hi Friend
i have a Clone like pic B
if i chanche that chips cyrcled in red like the pic A
Does my consult 3 will be good than before ....???
i have a probleme it disconnect a lot when diagnosizing cars ....
is there a solution for this ...???

Envoyé de mon SM-N9005
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
ORenult Clip 235 flavio69 0 59 26-03-2024, 11:34 AM
Last Post: flavio69
ORenult Clip 236 flavio69 0 134 22-03-2024, 12:44 PM
Last Post: flavio69
UInfiniti Looking for Nissan Consult j2534 drovid 5 326 16-03-2024, 15:01 PM
Last Post: domelec
ORenult Clip Renault v237 santanas 2 410 13-03-2024, 21:21 PM
Last Post: santanas
ORenult Renault Talismán DTC000292 PUMUKY1 1 152 12-03-2024, 20:24 PM
Last Post: corfumadness
ORenult CAN CLIP SOFTWARE ACTIVATIONS cracoucass 454 156,039 09-03-2024, 14:47 PM
Last Post: greenhorn
  Nissan Qashqai 2019 need cooding sorin.henea 1 87 04-03-2024, 09:05 AM
Last Post: xxmatixx
ODacia Clip 234 flavio69 14 1,336 27-02-2024, 21:36 PM
Last Post: Chad69
ORenult OpenPort 2.0 J2534 Reg files for CLIP ninjahwdp 7 829 26-02-2024, 22:10 PM
Last Post: drovid
  2009 Nissan Sentra Calibration file koziol 0 36 26-02-2024, 16:35 PM
Last Post: koziol

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content