Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
15-06-2015, 19:45 PM,
Post: #11
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
Kingauto 100% correct you need to relearn the throttle body with diagnostic tool and hit on head light side so no any issues in engine wiring & ecu .
|
|||
24-06-2015, 12:57 PM,
Post: #12
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
People thank"s for the ideias !
But I do not have any voltage on the motor throttle body ! this is pedal full press this is width the pedal not press do I have, to have some voltage on this terminal ?! Rigth ? throttle body relay seems to work ! what send voltage signal to the throttle body motor flap ? ART TECH GARAGE
|
|||
26-06-2015, 08:09 AM,
Post: #13
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
The throttle opening display at a duty ratio? Percent display
Duty ratio measurement do with an oscilloscope I think accelerator sensor 1 and 2's accelerator pedal |
|||
07-07-2015, 15:02 PM,
Post: #14
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
But Why car shout down when I engage 1º gear or other gear !
ART TECH GARAGE
|
|||
16-07-2015, 14:45 PM,
Post: #15
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
Does any one knows were is the throttle body relay ??
thank"s in advance ART TECH GARAGE
|
|||
29-08-2015, 22:48 PM,
Post: #16
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
Please check:
- ECTS fuse. - M+ and M- resistance on throttle body side connector- - M+ and M- voltage on the harness side connector. If all is well, then do the following: Accelerator Pedal Released Position Learning DESCRIPTION Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position sensor or ECM is disconnected. OPERATION PROCEDURE 1. Make sure that accelerator pedal is fully released. 2. Turn ignition switch ON and wait at least 2 seconds. 3. Turn ignition switch OFF and wait at least 10 seconds. 4. Turn ignition switch ON and wait at least 2 seconds. 5. Turn ignition switch OFF and wait at least 10 seconds. BASIC SERVICE PROCEDURE 2007 Armada Throttle Valve Closed Position Learning DESCRIPTION Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by monitoring the throttle position sensor output signal. It must be performed each time harness connector of electric throttle control actuator or ECM is disconnected. OPERATION PROCEDURE 1. Make sure that accelerator pedal is fully released. 2. Turn ignition switch ON. 3. Turn ignition switch OFF wait at least 10 seconds. Make sure that throttle valve moves during above 10 seconds by confirming the operating sound. IDLE AIR VOLUME LEARN (Manually) 1. Perform Accelerator Pedal Released Position Learning. 2. Perform Throttle Valve Closed Position Learning. 3. Start engine and warm it up to normal operating temperature. 4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order. 5. Turn ignition switch OFF and wait at least 10 seconds. 6. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds. 7. Repeat the following procedure quickly five times within 5 seconds. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. 8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. 9. Fully release the accelerator pedal within 3 seconds after the MIL turned ON. 10. Start engine and let it idle. |
|||
11-11-2015, 22:31 PM,
Post: #17
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
Manual procedure for Throttle learning and idle air volume learn.
Accelerator Pedal Released Position Learning DESCRIPTION Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position sensor or ECM is disconnected. OPERATION PROCEDURE 1. Make sure that accelerator pedal is fully released. 2. Turn ignition switch ON and wait at least 2 seconds. 3. Turn ignition switch OFF and wait at least 10 seconds. 4. Turn ignition switch ON and wait at least 2 seconds. 5. Turn ignition switch OFF and wait at least 10 seconds. BASIC SERVICE PROCEDURE 2007 Armada Throttle Valve Closed Position Learning DESCRIPTION Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by monitoring the throttle position sensor output signal. It must be performed each time harness connector of electric throttle control actuator or ECM is disconnected. OPERATION PROCEDURE 1. Make sure that accelerator pedal is fully released. 2. Turn ignition switch ON. 3. Turn ignition switch OFF wait at least 10 seconds. Make sure that throttle valve moves during above 10 seconds by confirming the operating sound. IDLE AIR VOLUME LEARN (Manually) 1. Perform Accelerator Pedal Released Position Learning. 2. Perform Throttle Valve Closed Position Learning. 3. Start engine and warm it up to normal operating temperature. 4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order. 5. Turn ignition switch OFF and wait at least 10 seconds. 6. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds. 7. Repeat the following procedure quickly five times within 5 seconds. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. 8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. 9. Fully release the accelerator pedal within 3 seconds after the MIL turned ON. 10. Start engine and let it idle. |
|||
13-11-2015, 00:47 AM,
Post: #18
|
|||
|
|||
RE: NISSAN MICRA K13 1.2 pedal not working, throttle DTC"s after crash
Solved !
The car goes to nissan dealer after words the car was from 2014 , and it only got 600km ! they not change anything , and they say it was the Throttle ! tank"s guy"s for you help and time best regards to all ART TECH GARAGE
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
nissan micra k12 wont start | coder | 0 | 33 |
14-04-2024, 15:29 PM Last Post: coder |
|
NISSAN CONSULT3 PASSTHRU DRIVERS VAS5054 | ritadj | 0 | 104 |
10-04-2024, 22:06 PM Last Post: ritadj |
|
Nissan micra - virgin dump for EPS | bboctavian | 0 | 46 |
05-04-2024, 11:44 AM Last Post: bboctavian |
|
2015 Nissan Rogue missing BCM | koziol | 0 | 44 |
05-04-2024, 00:59 AM Last Post: koziol |
|
Looking for Nissan Consult j2534 | drovid | 5 | 445 |
16-03-2024, 15:01 PM Last Post: domelec |
|
Nissan Qashqai 2019 need cooding | sorin.henea | 1 | 115 |
04-03-2024, 09:05 AM Last Post: xxmatixx |
|
2009 Nissan Sentra Calibration file | koziol | 0 | 58 |
26-02-2024, 16:35 PM Last Post: koziol |
|
Nissan Qashqai no cummunicate with ecm , many fault u1000 | TKservice | 0 | 61 |
23-02-2024, 06:59 AM Last Post: TKservice |
|
Glow plugs values Nissan x-trail t32 dci bad start | AlexM3F80 | 3 | 132 |
23-02-2024, 06:25 AM Last Post: AlexM3F80 |
|
nissan pickup 2005 new key | davito1 | 0 | 38 |
22-02-2024, 17:08 PM Last Post: davito1 |
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content