Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Renault Megane DCi Injection and CLIP
11-06-2015, 20:42 PM,
Post: #1
|
|||
|
|||
Renault Megane DCi Injection and CLIP
Hello to all once again.
Can anyone help/teach us/point us in the right direction. We bought a Megane (2003) 1,5dci with injection failure. We fitted another injection pump, common rail and injectors and did the timing belt and waterpump at the same time. The car had also been idle for some time, without a battery connected. Our friend brought his Bosch gadget from work and coded the injectors - the Megane refused to fire up. Our friend gave us another set of injectors and we fitted them - but then he couldn't get the Bosch tool again so we bought and installed a chinese CLIP, V140. It connects to the car and can automatically get the VIN. If you do automatic test of all computers, it says "Some Computers not Responding to Diagnostics" and under "Not Detected" it lists 120 - INJECTION 1232 - Variable PAS 756 - AIRBAG/PRETENSIONERS If you go into Programming , Select INJECTION , it successfully searches for data, click validate , validate info displayed , click ok to re-programming message , click next , It then checks battery voltage - with a new battery its 10.9 , with another battery (with jumpleads) + charger connected it reads 11.1 on clip even though at the terminals its 12.37 . Clip does transmission and then the following error message "FAULTY TRANSMISSION - CONTACT THE COMPUTERS CORRESPONDANT - REPROGRAMMING PROCEDURE INTERRUPTED" We are a newbie with CLIP so help would be greatly appreciated. In the meantime we are going to make those leads on the car spotless and try again. |
|||
11-06-2015, 23:33 PM,
Post: #2
|
|||
|
|||
RE: Renault Megane DCi Injection and CLIP
If I can understand it is that you can not find injeccion ECU. and airbag ECU ?? diagnostic diagram
if so it is necessary that you check communications line CAN if all goes well it is not necessary to reprogram anything .... (but if it goes wrong you will have to repair the CAN line) verify fault memory ECU Injecion ... if this ok when you give to crank or start you have to verify that there rail pressure (~ 200 bar), engine speed, speed camshaft (carefully. to be fine distribution belt, many people put so bad) |
|||
05-05-2016, 21:59 PM,
Post: #3
|
|||
|
|||
RE: Renault Megane DCi Injection and CLIP
I have this problem from time to time, it finally recognises the computer after starting the engine for some mysterious reason.
Another good reason for this problem is an incorrect configuration. For that you need to get into the config page and check that all factory fitted items are checked with a “YES” and all those not fitted with a “NO” Good Luck |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
CAN CLIP SOFTWARE ACTIVATIONS | cracoucass | 458 | 156,999 |
Yesterday, 13:20 PM Last Post: semiix |
|
CLIP 232 | flavio69 | 34 | 3,373 |
19-04-2024, 20:35 PM Last Post: alexbenz |
|
Clip Renault v237 | santanas | 7 | 1,014 |
11-04-2024, 08:13 AM Last Post: Gigan |
|
Which latest version of CLIP for RTL Sonde. | ninjahwdp | 7 | 829 |
10-04-2024, 12:57 PM Last Post: Gigan |
|
Renault Master 2.3dci no crank no fuel pump | goontii | 5 | 151 |
10-04-2024, 07:27 AM Last Post: pupu144 |
|
Clip 236 | flavio69 | 5 | 470 |
01-04-2024, 11:57 AM Last Post: flavio69 |
|
Clip 235 | flavio69 | 0 | 170 |
26-03-2024, 11:34 AM Last Post: flavio69 |
|
Renault Talismán DTC000292 | PUMUKY1 | 1 | 273 |
12-03-2024, 20:24 PM Last Post: corfumadness |
|
Clip 234 | flavio69 | 14 | 1,603 |
27-02-2024, 21:36 PM Last Post: Chad69 |
|
OpenPort 2.0 J2534 Reg files for CLIP | ninjahwdp | 7 | 982 |
26-02-2024, 22:10 PM Last Post: drovid |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content