Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
E60 EVO OABR to OBD Coding
10-04-2024, 14:22 PM,
(This post was last modified: 10-04-2024, 14:38 PM by painsage.)
Post: #11
|
|||
|
|||
RE: E60 EVO OABR to OBD Coding
(10-04-2024, 13:47 PM)NeRkO20 Wrote: and if you set your IP on laptop manually?I tested for wire continuity between the OABR and RJ45 at the end of the OBD cable when connected to car, all is fine. If i set ip adress manually i get the same result. I'm gonna measure the resistance and let you know. (10-04-2024, 13:49 PM)Node Wrote: If you measure resistance on OBD between rx and tx pairs, what do you get?Between TX+ and RX+ on my OBD port i get 155 Ohms. |
|||
10-04-2024, 15:46 PM,
(This post was last modified: 10-04-2024, 15:48 PM by Node.)
Post: #12
|
|||
|
|||
RE: E60 EVO OABR to OBD Coding
I meant between Tx+ and Tx-. And then Rx+ to Rx-. IMHO, given that ethernet pairs should be galvanically isolated, Tx+ to Rx+ you should get megaohms at least, so it feels like your wires are CROSSED! (meaning either Tx+ is actually Rx- or Rx is actually Tx-). Well, either that or you have a short somewhere.
|
|||
10-04-2024, 17:39 PM,
Post: #13
|
|||
|
|||
RE: E60 EVO OABR to OBD Coding
(10-04-2024, 15:46 PM)Node Wrote: I meant between Tx+ and Tx-. And then Rx+ to Rx-. IMHO, given that ethernet pairs should be galvanically isolated, Tx+ to Rx+ you should get megaohms at least, so it feels like your wires are CROSSED! (meaning either Tx+ is actually Rx- or Rx is actually Tx-). Well, either that or you have a short somewhere. Wire continuity is fine, so short is not it 100%. You think i swapped the wires around? Do you have OABR pinout with where what pin should be? I don't know how i would even get a connection if its swapped around? My PC can see that there is a connection on the LAN port. |
|||
12-04-2024, 10:54 AM,
Post: #14
|
|||
|
|||
RE: E60 EVO OABR to OBD Coding
Hello all, managed to get OABR coding working no problems. Only need 4 wires for TX, and RX from OABR to OBD. Node was correct, i switched RX and TX around, after putting them how they should be, all is working fine. No need for ETH_A or any other things for EVO to work with OABR.
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Bmw F34 trailer hitch coding ? | Cryjack | 2 | 64 |
27-04-2024, 20:27 PM Last Post: dumitru.o |
|
F20 LCI2 black panel cluster coding | sqorpius | 10 | 2,087 |
27-04-2024, 06:51 AM Last Post: hamzettin |
|
FDL coding BMW Apps | Mugga | 3 | 197 |
26-04-2024, 18:06 PM Last Post: Mugga |
|
Coding a F80 M3 race car | PeterY | 10 | 564 |
25-04-2024, 23:32 PM Last Post: Furgus |
|
NBT Evo CAFD missing after coding error | Mugga | 13 | 620 |
24-04-2024, 22:47 PM Last Post: Mugga |
|
6wb cluster swap and coding | xMoses | 4 | 259 |
22-04-2024, 19:07 PM Last Post: NikolaIMRS |
|
M performance brake DSC2 SBRE coding | Ckh091020 | 3 | 237 |
22-04-2024, 12:58 PM Last Post: Ckh091020 |
|
pulling both paddles put transmission into neutral coding | tintoverano | 1 | 132 |
22-04-2024, 12:42 PM Last Post: raresh.tazz |
|
G01 2019 X3 - ATM Replacement/Coding Help Needed | jchisholm17 | 10 | 482 |
18-04-2024, 21:44 PM Last Post: jchisholm17 |
|
TMS FRM3 F10 Coding issue | mj_mj_mj | 17 | 1,952 |
16-04-2024, 09:30 AM Last Post: user_530d |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content