Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. Martech

  2. ATM - Balkan

    atm balkan file service
  3. Porsche piwis

  4. MOD FILES

  5. ProCarDiag

  6. ECU CHIPS



Post Reply 
DO NOT BUY or use Nissan Consult III+ chinese clone!
24-08-2015, 13:14 PM
Post: #1
UNissan DO NOT BUY or use Nissan Consult III+ chinese clone!
This is to warn everyone who decide to buy Chinese clone of NISSAN CONSULT III Plus tool.
I purchased the tool from this seller: http://www.auto-diagnostic-tool.com/por....104&id=261 which has caused several damage to the car while the tool was connected - ECM and BCM modules died
I have to add that I used to work with genuine Nissan Consult III Plus software quite frequently so it's not caused by lack of knowledge!!!


Chinese clone also did not work as genuine NISSAN tool. It could not detect car VIN, communication was dropping most of the time, etc. etc...


Stay away of Chinese crap if you like your car..
Reputation: +1 - Renopower [+1]
Find all posts by this user
Quote this message in a reply
 Thanks given by: Renopower , nenad.gorgi
24-08-2015, 16:27 PM
Post: #2
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
It depends of how much you buy,me personal have not this VCI but I know ppl's who are using clone VCI and have no problem,so not generalize+not think I'm not an chinese market fan but maybe you chose to buy a cheap version or simply you have bad luck
Find all posts by this user
Quote this message in a reply
 Thanks given by: alfabit , mladen76 , Renopower , Ashraf6119 , dvdpgn , eudin77
15-07-2016, 05:27 AM
Post: #3
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
The clone C3+ is expensive in China. But it not same as original C3+ at all, Only has the same cover. It can't support several function of C3+ etc. reprogramming.
Find all posts by this user
Quote this message in a reply
15-07-2016, 08:24 AM
Post: #4
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
Chinese crap allows to scan and clear errors, and the best case scenario to change some settings. But it cannot handling monitoring functions i.e. you set to monitor ECM but after a while, it dropps connection to OBDII and laptop and the only thing you can do is to kill Consult app and reconnect VCI from OBDII and the laptop. In general, it is very unstable device, which if get disconnected in crucial moment, will damage some ICU.

It is fraud to sell this chinese crap for such high amount, when better job can do full version of Xpro3 with hacked EasyDiag OBD scanner (which support all makes on the globe). The other thing is that the seller is lying & cheating. They didn't want to accept item return and when they connected remotely to my laptop, didn't even have basic knowledge of how to using it. They only managed to check whether VI2 driver was installed properly.
I don't mind what you do with your money, I just wanted to warn innocent people who decide to spent their hardly earned money on this tool. BE AWARE OF THESE LIMITATIONS AND STAY AWAY OF FRAUDELENT PRACTICES OF AUTO-DIAGNOSTIC-TOOL.
Find all posts by this user
Quote this message in a reply
 Thanks given by: Diagnostix
15-07-2016, 10:37 AM
Post: #5
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
Thank you for you opinion
the chine clone it is bad result
Find all posts by this user
Quote this message in a reply
15-07-2016, 16:12 PM
Post: #6
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
Yes. It has been a well known fact for years. If you want to use this tool then buy genuine new or used from usa.
Reputation: +1 - Balyanchic [+1]
Find all posts by this user
Quote this message in a reply
 Thanks given by: Balyanchic
06-03-2017, 02:54 AM (This post was last modified: 06-03-2017 04:20 AM by Clusters.)
Post: #7
RE: DO NOT BUY or use Nissan Consult III+ chinese clone!
(15-07-2016 16:12 PM)Diagnostix Wrote:  Yes. It has been a well known fact for years. If you want to use this tool then buy genuine new or used from usa.

I badically learned if i buy something from china dont expect warranty. Been burned a few times with other tools. As far as consult 3 goes i use my cardaqm j2534 and consult3 software minor changes and it workes no programming. I have only tried 3 cars. I think i got the software from hasoon2000 here or another forum not sure.
Find all posts by this user
Quote this message in a reply
Post Reply 


Bookmarks

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Nissan pinout ??? in flyingdutchy81 1 24 Yesterday 20:09 PM
Last Post: sixcode
UNissan Nissan Consult III+ Plus V71 Complete in fantomel 22 1,757 16-10-2017 13:31 PM
Last Post: Starmobile
  2007 NISSAN TITAN TCM flash file needed in koziol 2 83 16-10-2017 06:48 AM
Last Post: robertbeam26
UNissan Nissan & Infiniti Fast EPC [09.2017] in Treypheos 0 53 16-10-2017 01:48 AM
Last Post: Treypheos
  Free Nissan BCM pin code old and new for android in Kukuh Septianto 0 90 13-10-2017 00:19 AM
Last Post: Kukuh Septianto
  Nissan sentra need millage change in wphonetei 0 74 09-10-2017 12:57 PM
Last Post: wphonetei
  Nissan Consult 3 installation problem in KRIS-CAR 5 258 21-09-2017 13:37 PM
Last Post: hasoon2000
  Nissan Qashai injectors coding software-device in tomaszp 0 139 08-09-2017 23:35 PM
Last Post: tomaszp
UNissan Nissan Consult 64.11 - patched in Treypheos 8 1,276 25-08-2017 10:30 AM
Last Post: kmaverick
UNissan Nissan PIN Calculator - New & Old in Treypheos 16 3,843 23-08-2017 22:32 PM
Last Post: asha

Forum Jump:


User(s) browsing this thread:
1 Guest(s)

Return to TopReturn to Content