CarTechnoloGY
VCDS 17.8.1 MULTILANGUAGE FULL - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55)
+---- Thread: VCDS 17.8.1 MULTILANGUAGE FULL (/showthread.php?tid=26509)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

RE: VCDS 17.8 MULTILANGUAGE FULL - b0gdi - 29-09-2017

(29-09-2017, 15:03 PM)allop Wrote:  What vid pid has your interface?
Use Mprog to write ftdi_mprog_BMBL.ept
it has the folowing USB\VID_0403&PID_FA20&REV_0400

RE: VCDS 17.8 MULTILANGUAGE FULL - ninja_zx11 - 29-09-2017

Which interface is better?

First or second in the picture?Thanks

RE: VCDS 17.8 MULTILANGUAGE FULL - DTech - 29-09-2017

Both are ok, check soldering on them and special to lm voltage regulator. that tends to be a problem. second one with aes have been reported to have shorter obd pins and not make proper contact in cars.

RE: VCDS 17.8 MULTILANGUAGE FULL - ninja_zx11 - 29-09-2017

(29-09-2017, 23:50 PM)DTech Wrote:  Both are ok, check soldering on them and special to lm voltage regulator. that tends to be a problem. second one with aes have been reported to have shorter obd pins and not make proper contact in cars.

Thanks Dtech!! will check it.I found second one gets quite warm after some time especially voltage regulator.

RE: VCDS 17.8 MULTILANGUAGE FULL - allop - 01-10-2017

Remove jumpers and try again!

RE: VCDS 17.8 MULTILANGUAGE FULL - Michael1 - 01-10-2017

Hi please is this interface possible update with USBASP flasher and where connect.
Thanks in advance
   

RE: VCDS 17.8 MULTILANGUAGE FULL - fantomel - 01-10-2017

(01-10-2017, 14:35 PM)Michael1 Wrote:  Hi please is this interface possible update with USBASP flasher and where connect.
Thanks in advance
that is shit chinese invention with nec chip, good for bin smile not to reflash

RE: VCDS 17.8 MULTILANGUAGE FULL - b0gdi - 01-10-2017

(29-09-2017, 15:18 PM)b0gdi Wrote:  
(29-09-2017, 15:03 PM)allop Wrote:  What vid pid has your interface?
Use Mprog to write ftdi_mprog_BMBL.ept
it has the folowing USB\VID_0403&PID_FA20&REV_0400

Hello again, i flashed the ftdi with the ftdi_mprog_BMBL.ept. I connected the interface to USB and 12V and now HWType says:
FW Version : 1.79
HW Version : 0x44
Identification : OD<
When I try to write the new firmware with vagcom_eewrite it says "Not in bootloader mode". Does it mean that i need to program it with external programmer? Thanks

RE: VCDS 17.8 MULTILANGUAGE FULL - papito56 - 01-10-2017

(05-08-2017, 19:46 PM)DTech Wrote:  Tested on rl and rq interfaces, not on bl since are so so old. but feel free to try and see. you will see if it works or not. if not use usb upgrader and put back old dump.


HI: After updating I get this feedback (USB library version 03.02.07
USB Drive Versions 02.10.00
Interface: not found!sad

RE: VCDS 17.8 MULTILANGUAGE FULL - ninja_zx11 - 01-10-2017

(01-10-2017, 17:32 PM)papito56 Wrote:  
(05-08-2017, 19:46 PM)DTech Wrote:  Tested on rl and rq interfaces, not on bl since are so so old. but feel free to try and see. you will see if it works or not. if not use usb upgrader and put back old dump.


HI: After updating I get this feedback (USB library version 03.02.07
USB Drive Versions 02.10.00
Interface: not found!sad

Try to plug it in a different USB port.I had a same issue until i plugged it in a different port and it started working.Now it works on all ports.